可以认为颗粒与基体间弱界面的解聚是熔融石英颗粒复合材料韧化的原因。
The decohesion of the weak interface between particle and matrix may be considered as the origin of toughening.
评述了具有弱界面结构的可加工陶瓷的研究进展。
The research progress in machinable ceramics with weak interfaces in microstructure was reviewed in this paper.
Q 2 35钢经冷轧—时效—再结晶处理后，钢中存在大量弱界面。
After cold rolling, aging and recrystallization treatment, there are many weak interfaces in Q235 steel.
只有切线方向的位移间断，而法线方向位移连续的弱界面称之为滑动界面。
The imperfect interface with a continuous normal displacement and a jumped tangential displacement is called a sliding interface.
本文研究线弹簧型弱界面颗粒增强复合材料，在比例加载条件下的简化塑性模型。
A simplified model is proposed for plasticity in particle-reinforced composite materials with linear spring-type imperfect interfaces under proportional loading.
结果表明，弱界面有阻碍位错运动、转主裂纹扩展方向的作用，可形成分层断口。
The results showed that the weak interface can block the motion of the dislocations and change the propagation direction of the main crack, and result in forming lamella fracture surface.
结果表明，弱界面有阻碍位错运动、偏转主裂纹扩展方向的作用，可形成分层断口。
The results showed that the weak interface can block the motion of the dislocations and change the propagation direction of the main crack, and result in forming lamella fracture surface.
采用线弹簧型弱界面模型来模拟柔性涂层，研究柔性涂层对复合材料宏观弹性模量的影响。
The effect of soft coatings on the elastic moduli of composite materials is studied, in which the coating is modeled by a linear spring type imperfect interface.
提出了一种利用拉伸法和剪切法测定内生复合板钢板弱界面拉伸强度及剪切强度的测试方法。
A new method was given to test the cohesion strength of weak interface of DISC by tensile tests and shearing tests.
通过力学性能测试、扫描电镜及透射电镜观察，研究了冷轧压下量及时效温度对内生复合钢板弱界面结合强度的影响。
Mechanical properties testing, SEM and TEM was used to study the effects of cold rolled reduction and aging temperature on the cohesion of the weak interface of DISC.
结果表明，现行的单钢管桩属于界面的粘结破坏，承载力低，变形能力弱，不能充分发挥材料特性。
Single pipe pile shows sliding failure at interface and cannot utilize the strength of material; the bearing capacity and deformation ability are low.
在复合材料中由于制备工艺或后期损伤导致的弱结合界面，界面破坏为主要的复合材料破坏机制。
Interface breakage will be the main fracture mechanism if the interface bonding is weak because of the damage during the composites preparation.
只需简单选择界面柔度系数，可方便地处理界面理想粘贴、弱粘贴和脱层三种界面粘贴状况。
Three kinds of interfacial bonding conditions, perfect bonding, weak bonding and delamination, may be conveniently dealt with by choosing interfacial toughness coefficients.
然而，几乎和弱间化合物很容易在焊接界面形式在传统焊接过程中的组成范围广泛。
However, hardly and weakly intermetallic compounds are easy to form at welding interface in conventional welding process in wide composition range.
通过等离子体处理法、氧化法等各种物理和化学的方法对UHMWPE纤维表面进行改性处理，可不同程度改善其耐热、界面、抗蠕变等弱性。
The weak heat resistance, interface and creep resistance of the fiber can be improved differently by the surface modification using various physical and chemical methods such as plasma and oxidation.
通过双材料受压试验研究了弱奇异性界面端的界面初始脱粘点的位置问题。
The interface initial debonding location problem was studied through the push down test.
结果农明，碳没有被除尽，弱的碳界面层依然存在，没有增强界面结合强度。
The results indicate: a bit carbon was removed, and weak interphase joint exist still and did not build up the boundary strength.
结果农明，碳没有被除尽，弱的碳界面层依然存在，没有增强界面结合强度。
The results indicate: a bit carbon was removed, and weak interphase joint exist still and did not build up the boundary strength.
应用推荐