因此，我们提出了应变测量的新技术。
Therefore, we proposed a new technique for strain measurement.
其次，设计了分布式光纤光栅温度、应变测量系统。
Second, temperature and strain measurement system of distributed FBG is designed.
本文介绍了利用应变测量技术测量角加速度的方法。
This paper introduces the measurement of angular acceleration with strain measuring technique.
接着对缺陷区域进行主应变测量和安全成形裕度预测。
Then the principal strain measurement and forming safety margin prediction in defect regions are conducted.
由于工作温度较高，所以需采用高温应变片来组成应变测量电桥。
Because it has a high working temperature, the high temperature strain gauge is necessary in composing the strain measurement electric-bridge.
在光纤传感器广泛的应用领域当中，应变测量是最重要的部分之一。
Strain measurement is one of the most important fiber sensing application areas.
给出了应变传感器进行应变测量时的温度补偿公式与工程实施方案。
The formula of temperature compensation and the project of construction during strain measuring are presented.
详细介绍了电阻式应变测量系统的组成、系统静态标定的方法与步骤；
This paper described the consist of the resistance strain measure system and the approach of static calibration in detail.
CJ P型混凝土内部应变计主要用于混凝土建筑结构内部应变测量。
CJP concrete internal strain meter is designed for measuring the internal strain of architecture concrete.
应变测量基础——介绍应变，应力，印制板弯翘的概念以及应变片等。
Fundamentals of strain Measurement -definition of strain, stress, board flexure and strain gages.
这里对动应变测量系统进行分析，并在实测中验证了该测量系统的功能。
The paper has analyzed the dynamic strain measurement system and verified the functions of it through experiment.
介绍了应力应变电测技术的基本原理，分析和设计了电阻应变测量电路。
The basic principle of strain electronic measurement technique is introduced. The circuit of strain measurement with bonding resistance is analyzed and designed.
该装置的两个关键测量分系统是天平测量系统及旋翼桨叶应变测量系统。
Two of them are the balance measurement subsystem and the blade strain gauges measurement subsystem which are very important to the facility.
应变测量系统主要由光源、传感光纤、光电探测器和信号处理电路组成。
The above system chiefly consists of light source, optic fiber sensor, photo detector and signal processing circuit.
为了解决这个问题，我们改变了应变仪配置，缩短了用于应变测量的距离。
To resolve the problem, we changed the stain gauge arrangement and shortened the distance used for strain measurement.
材料力学应变测量实验中，试件在小负荷作用下所产生的应变信号十分微弱。
In the strain-data measured experiments of material of mechanics, the bar generates weak strain signal by the less force functioning on the bar.
采用电阻应变测量技术研究了带有初始随圆度的弯管在纯内压作用下的应力分布。
The stress distribution of a curved pipe with an initial elliptic cross section under internal pressure was studied by using electric resistance strain method.
利用电阻应变计开发的动应变测量系统，成功的实现了机械振动信号的动态检测。
The dynamic test in signal detection of mechanical vibration are realized by using resistance strain gauges.
分析了适用于动态应变测量的光纤光栅传感器所应满足的条件，并进行了相关实验。
Analyzed the conditions applying for the dynamic strain measurement of fiber grating sensor, and did some correlative experiments.
为验证大棚骨架的强度，用农机测试中的应变测量法，来探索其内部应力的变化情况。
The strain test in the agricultural machinery field was used to probe the stress variation inside a frame in order to examine the strength of the plastics greenhouse frames.
试验结果表明，对于特殊的环境或者特殊结构下的应变测量，FBG具有无可比拟的优势。
The results indicate that FBG is unparalleled in strain measurement under special circumstances or structure. The fifth part is the most important point of this paper.
这种方法可以解决无机应变胶高温绝缘电阻过低的问题，并可以提高高温应变测量的精度。
It can solve the difficulty of low insulation resistance of high temperature strain gage adhesives and can raise the accuracy of high temperature strain measurements.
首先，介绍了电阻应变测量法的基本原理，应变测量的理论、方法以及相关的信号处理知识。
First, the basic principle of the strain measurement with bonding resistance, theory of strain measurement, method and the relative signal disposition are introduced in the dissertation.
文中介绍了管内海水冻结过程、海水过冷温度、结冰水温、轴向冻胀力以及管体应变测量结果。
This paper expounds the test results of the freezing Process of sea water, the excessive cold temperature of sea water, the frozen water temperature, sea water frost heaving force and the tube strain.
组装过程中应变测量的典型变异来自：应变片类型，粘贴工艺，定位准确度学和数据采集系统。
Typical sources of variation in assembly line strain measurement include: strain gage type, attachment process, placement accuracy to location target and data acquisition system.
本文简要介绍了高温应变测量原理和技术在大型汽轮发电机转子护环热套应力测试中的成功应用。
The technique and its principle of high temperature strain measurement are introduced to determine heat sleeve stress about rotor retaining ring of large turbogenerator.
通过对钢制内压球形封头和圆筒形容器的应变测量及应力进行分析，发现了数据中存在的一些问题。
By measuring the strain of the steel internal pressure vessel which has a hemispherical head and a cylindrical shell, analyzing the stress, we discover the data exists the problem.
一份完整的应变测量报告必须包括：数据摘要，测量板和元器件的图片，应变曲线以及原始数据等。
A completed strain report must consist of: Data summary, Pictures of boards and components, strain graphs and Raw Data files.
针对采用压电元件的动态应变测量系统的低频失真问题，提出一种采用数字滤波器的低频特性补偿方案。
A digital filtering method is proposed for compensation of the low frequency characteristics of piezoelectric dynamic strain measurement system.
针对采用压电元件的动态应变测量系统的低频失真问题，提出一种采用数字滤波器的低频特性补偿方案。
A digital filtering method is proposed for compensation of the low frequency characteristics of piezoelectric dynamic strain measurement system.
应用推荐