应用有限元计算方法研究了腰椎段的应力应变分布规律。
We have studied the stress and stain distribution of lumbar using FEM.
同时，对变形区内的应力应变分布特征作了较详细的分析。
In addition, the distribution characteristics of mean stresses and mean strains in the deformation zone have been investigated.
通过线性分析初步了解了轴压下仓壁柱承钢筒仓的应力应变分布特性。
At first, linear stress analyses were performed to investigate the stress-strain distribution of axially compressed column-supported steel silos with engaged columns.
由计算的应力应变分布形态所展示的亚微观断裂性质与实验观察相符。
The microscopic fracture mechanism revealed by these stress distributions coincides with experimental observations.
探讨了剪跨区内应力应变分布变化规律；分析了试件的破坏过程及状态。
This paper explores the regularities of the distributions of stresses and strains within the shearing spans and analyses the failure procedures and the failure modes of the specimens.
由于起落架的结构比较复杂，很难通过理论计算得出准确的应力应变分布。
It is difficult to calculate theoretically the exact distribution of the stress and strain because of the complex structure of landing gear.
此处环板的径向应力应变分布成斜直线，高应力应变区域集中在环板内部。
Distributing of stress and strain on 45o section is declining line, high stress and strain focus on inside of enforced loop plane.
这可能是由于应力应变分布、氧化物、界面结合情况改变等综合因素造成的结果。
This shows that interface curves becomes more and more complex. This may be due to the distribution of stress and strain, oxide, condition of interface and so on.
详细地分析了该条件下的坯体致密规律，应力应变分布规律和粉末质点流动规律。
Finally the compacting principle of the billet, strain and stress distribution and powder particle flowing rule are analyzed in detail under this condition.
辊模拉拔变形区内的应力应变分布特征完全不同于固定辊模拉拔，而倾向于轧制过程。
The distribution of stresses and strains in the deformation zone under roller dies drawing is different from that under fixed rolls drawing, but tends towards rolling.
分析发现，与无缺陷焊点相比，气孔使焊点中应力应变分布发生了改变，使焊点疲劳寿命缩短；
The effect of gas hole location on SMT solder joint fatigue life has been analyzed by finite element method .
其次，本文使用ANSYS通用有限元策略对桥面铺装模型进行浅析浅析并得出它们的应力应变分布。
Secondly, the model of deck pavement is analyzed by finite element software ANSYS to get its stress and strain distribution.
运用解析方法对量子点的结构进行分析，通过对积分核函数进行计算，可以得到各种量子点结构的应力应变分布。
An analytical method based on Green's function for calculating strain filed in quantum dot structures of arbitrary shape was presented.
从计算结果中提取应力应变云图显示了工件及刀具的应力应变分布情况，以此对切削过程中应力应变的变化进行了分析。
The images from result show the distribution of stress and strain and supply basis for the analysis to the change of stress and strain.
建立了负重轮的三种三维有限元力学模型，在考虑三重非线性的情况下，用ANSYS有限元分析软件计算了负重轮的应力应变分布。
Under the condition of three kinds of nonlinearity the stress and strain distribution of the road wheel is calculated with finite element analysis software ANSYS.
对计算得到的轮包成形极限图、应力应变分布图进行了分析，并采用基于网格分析法的物理实验验证了有限元建模的可靠性和正确性。
The validity of modeling, the accuracy and reliability of simulation results for stamping forming processes of hubcap are affirmed on the basis of grid strain analysis technique.
本文以杭州湾跨海大桥北航道非通航孔桥为工程背景，对大跨度预应力混凝土箱梁锚固区混凝土的应力应变分布特征进行了分析研究。
A study of the stress and strain distribution of anchorage zone in a long span PC box girder was undertaken in the background of Hangzhou Bay Bridge project.
采用有限元数值模拟对环壳零件成形过程中不同压下量下毛坯各节点的应力应变分布及变化规律进行了分析，获得了环壳零件冲压过程的成形规律。
With the FEM simulation, the strain and stress of each node under different deformation stage are analyzed and the common forming law of this ring shell container is obtained.
只有小裂纹扩展到足够长并钝化到足够宽，才能够影响主裂纹的扩展及其前端应力、应变的分布。
Only if this short crack extends long enough and blunted wide enough, can it affect the principal crack extension and the distribution of stress and plastic strain.
通过分析可得，粘贴层剪切应力的分布与致动器端部附近的应变分布有相似的特征。
This paper shows that the shear stress distribution in bonding layer has similar characteristics as the strain distributions near the ends of the actuator.
目的：分析不同倾斜种植对种植体界面应力、应变及位移分布状况的影响。
Objective: To analyze the influence of different tilted angle on the distribution of the stress, strain and displacement on the implant_bone interface.
应用有限元法，编制子程序，研究了重力坝应力和应变分布规律。
Applying finite element method and programming subprogram to study distributed regularities of concrete gritty dam's stress and strain.
研究了铺装层应力场分布，回归统计了随轴载作用次数增加，应力应变的变化规律。
The regression statistical method has been used to analyze the law of stress and strain as The Times under the function of axial load increases.
模拟得出了变形过程中的应力应变状态和错动量分布。
Cauchy stress, plastic strain and slipping-off distribution in the workpiece during drawing process are given.
用塑性理论求得杯形件拉深成形工艺过程中凸缘部分的应力与应变分布的解析解。
The paper mainly focuses on the analysis of the distribution of stress and strain in the flange of a cup-shaped part during deep drawing, according to the plastic mechanics theory.
同时研究了合金颗粒和基体应力、应变分布，以及轧制量的影响。
The distributions of stress and strain after hot rolling and effects of milling thickness were investigated with the evolvement of state from sliding to sticking.
同时研究了合金颗粒和基体应力、应变分布，以及轧制量的影响。
The distributions of stress and strain after hot rolling and effects of milling thickness were investigated with the evolvement of state from sliding to sticking.
应用推荐