同时节点的应力分布也得到改善。
最后分析了抓爪的应力分布。
给出了应力分布、压力分布及速度场。
The stress and pressure distributions, and velocity fields are given.
而其热应力分布问题是其中的主要因素。
And the distribution of thermal stress is one of the primary factors.
目的：了解正常人腰椎椎体的应力分布特点。
Objective: To realize normal stress distribution of lumbar vertebral body.
目的：研究坐位旋转手法时对腰椎内在应力分布的特点。
Objective: To study the traits of intra-stress distribution of lumbar during rotatory manipulation.
同时，钎缝圆角几何形状对这一热应力分布有重要影响。
Meanwhile, the fillet geometry has played an important role on this thermal stress distribution.
本文采用有限元法分析了板上芯片（COB）的热应力分布。
The finite element method was used for analysis of heat stress in chip on board(COB).
本文采用有限元法分析了板上芯片(COB)的热应力分布。
The finite element method was used for analysis of heat stress in chip on board (COB).
目的建立水下爆炸性冲击波实验模型并分析其应力分布特性。
Objective To develop the experimental model for explosive blast under water and analysis its distribution characteristics.
这导致应力分布不均匀地传导至深层软骨及其下面的软骨下骨。
This results in uneven distribution of stress transmission to deeper layers of cartilage and to the underlying subchondral bone.
计算结果表明，先弯曲再拉伸时应力分布规律更利于减小回弹。
The simulative results show that stress distribution under stretching with superimposed bending is more advantageous to the reduction of spring back.
数值计算结果给出了管材在不同的拔制阶段的应变与应力分布。
The distributions of the strain and the stress of the pipe are obtained by the numerical computation.
此法与一般的计算方法相比在控制截面的应力分布方面有大的差别。
This method differs greatly from the present general calculation method in the stress distribution of controlled section.
研究单搭接接头胶缝中预留间隙对接头拉剪强度和应力分布的影响。
The effect of the recessing on the strength and stress distribution of adhesively bonded single-lap joints is discussed.
但后两者都是影响井壁应力分布和岩石力学性能而造成井壁不稳定。
The last two factors induce borehole instability both by affecting stress distribution around wellbore and material properties of rock.
根据端部所呈现的应力分布规律，提出了确定端部合理结构型式的方法。
According to the regulation of axial stress distribution, a way to design the rational end construction is given.
通过膜应力和弯曲应力分布的特点，验证了板的屈曲过程的非线性特性。
The characteristic distributed for the membrane stress and crooked stress, has proved the bucking course of the panel is non-linear.
本文用三维弹塑性有限元法计算了含圆孔对称复合材料层板的层间应力分布。
In this paper, the interlaminar stress distributions of symmetric composite laminates with a hole are predicted by the three-dimensional elastoplastic finite element method.
通过大量计算，对应于几种主要的载荷工况，得到了车桥横梁的应力分布规律。
Through a large amount of calculation, the stress distribution Pattern of beam axle is obtained for some main load cases.
利用弹塑性理论建立了孔冷挤压的载荷、位移、应力以及残余应力分布表达式；
The expressions of load, displacement, stress and residual stress distribution for hole cold_extrusion process are established by using elastic_plastic theory.
与光弹性方法不同的是声弹性方法不需要透明模型，能直接测量材料的应力分布。
Different from photoelastic method, acoustoelastic method does not need transparent model and can measure stress distribution of material directly.
依据受力与变形理论较为精确地给出了搭接接头侧面角焊缝中的剪应力分布规律。
According to the theory of bearing forces and deformations this paper gives distribution laws of the shearing stresses in the side fille welds of overlap connection with comparative accuracy.
本文试对框架的计算简图和悬挑板转角处应力分布两个设计中常见的问题作一探讨。
This paper discusses the common problems in the design of frame calculation sketch and stress distribution at corner of the jetted plate.
用有限元方法计算了铝热离心法制备不锈钢内衬复合钢管过程中的残余热应力分布。
The thermal stress distribution of the stainless steel lined composite steel pipe prepared by centrifugal-SHS process was calculated by the finite element method under thermoelastic assumption.
有限元计算表明，网格墙在轴力和水平力作用下的正应力分布与实体墙总体上一致；
The finite element analysis showed that the normal stress distribution of the grillage wall was about the same as that of the solid wall.
方法：用二维有限元法分析阻萌力减少前后下第一磨牙牙周组织内应力分布的变化。
Metbods: a two dimensional finite element model was built up to analyse the stress within the periodontal tissue of the first molar, with a reduced tooth eruption-resistant force.
数额的残余应力可能指向一个解决方案，而应力分布，可以建议其他所需加工改建。
The amount of residual stresses may point to one solution, while the distribution of stresses may suggest other required processing alterations.
数额的残余应力可能指向一个解决方案，而应力分布，可以建议其他所需加工改建。
The amount of residual stresses may point to one solution, while the distribution of stresses may suggest other required processing alterations.
应用推荐