汽车碰撞时左侧的翼子板撞坏了。
一种车身，包括翼子板和前灯组件。
拧紧扰流板和附加翼子板。
由于车门区域仍装有防溅护板，请小心地拆下翼子板。
Remove the wing carefully since the splash guard for the door area is still fitted.
并结合模具的调试过程对外覆盖件翼子板的成形过程进行了模拟。
The simulation of front side panel forming process has been car-ried out with die adjustment.
提出了一种摄像机标定方法并应用于某轿车翼子板的非接触检测。
A camera calibration method was put forward and applied to non-contacting detection for the front fender of a car.
对卡车翼子板滚塑成型原料、工艺条件、制件和模具设计进行了研究。
For rotational molded truck fender, raw material, processing conditions and the design of part and mold were studied.
飘的子板歧管，硬或柔性管道，连接器和夹具原名与传统的配电系统。
Gone are the sub plate manifolds, hard or flexible piping, connectors, and clamps formerly known with traditional distribution systems.
演示子板包含温度和光传感器、一个三轴加速计、8 个三色 LED以及两个按钮开关。
The demonstration daughterboard contains temperature and light sensors, a three-axis accelerometer, eight tricolour LEDs, and two pushbutton switches.
将该方法用于某汽车翼子板成形模拟，并与增量法模拟结果及实验结果进行了对比。
This method was applied to simulate an automobile front fender, and its results were compared with the results of experiment and simulation by incremental method.
以奥拓轿车翼子板为例，验证了用相似学原理建立的覆盖件工艺决策方法的实用性。
The example of Alto car fender is taken, and practicability of cover panels planning system built by similarity theory is verified and experienced.
必要时，还可以通过5 个通用I/O插脚和4 个高电流输出插脚增加更多的子板。
Additional daughterboards can be added if necessary through five general-purpose I/O pins and four high-current output pins.
基于此，进一步分析了模具几何参数和工艺参数对回弹量的影响，为翼子板模具设计提供理论依据。
Based on this, the influence of the die geometry and process parameters on springback was further analyzed, which provides a theoretical basis for the front fender dies design.
采用理论分析、试验制品设计与实验结合的研究方法，研究卡车翼子板旋转模塑成型试验制品设计问题。
The experimental part design of rotationally molded truck fender was studied by combining theory analysis, experimental part design and experiment.
根据MPC860T的特点，我们把模块化路由器的设计分为主板设计、插槽设计、通信子板设计三个部分。
We divide the whole design into three parts based on the characters of MPC860T: the main board design, the self-define slot design and the communication board design.
罐体实际上是一个可以与scratchbuilt甲板，梯子，孵化，后翼子板等德士古与计算机标识作出啤酒。
Tank body is actually a beer can with scratchbuilt deck, ladders, hatches, rear fenders etc. Texaco logos made with computer.
每块波前处理子板的校正量输出为120路，波前处理主板的最大扩展能力为10块，整个系统可实现1 200路校正量的输出。
As each wave-front processing sub board can promote the output of 120 road and the maximum expansion capacity of the main board is 10, the system can reach the momentum of the output in 1 200 road.
介绍了板料成型CAE软件CADEM主要理论，并以汽车外覆盖件翼子板的拉延模具开发为例，阐明了CAE技术在模具开发中所起的重要作用。
The core theory of sheet metal forming simulation software CADEM is introduced. Taking the development of drawing die for front fender as an example, the role of CAE technology is emphasized.
火焰一下子窜到了天花板。
为了防止新鲜的莓子在冰箱里冻完后变成糊状，应该把它们彻底洗净，拍干，放在烤板上。
To prevent fresh berries from turning to mush in the freezer, wash the fruit thoroughly, pat it dry, and place on a cookie sheet.
将烤板放在冰箱里直到莓子冻上，然后再把它们放进密闭容器中。
Place the cookie sheet in the freezer until the berries are frozen, then pack the berries in airtight containers.
天花板上的灯闪着一串火花碎裂，酒馆里一下子暗了许多。
On the ceiling, a light fixture shattered in a shower of hot sparks, plunging much of the bar into darkness.
日本板硝子株式会社和其他公司的子公司都面临着同样的问题。
Subsidiaries of Nippon Sheet Glass and others have also faced unrest.
至于背景中白色写字板上的那些公式，已经成为每周新的一集的主要部分，Saltzberg提供了描述磁单极子的经典图像和方程。
As for the white board equations in the background that have become a staple of each weekly episode, Saltzberg provided classic diagrams and equations describing magnetic monopoles.
但是麦克 布隆贝格说，“我可不知道什么是绿色岗位，把太阳板放到屋顶是电工的事，你可不能把一个失业人员一下子就变成电工，让他来做这事。”
But “I’m not sure what a green job is, ” says Michael Bloomberg, a billionaire businessman turned mayor of New York.
展览馆巨大的面积和高高的天花板确实吻合了小野洋子的惊悚元素，她的多媒体展品《DasGift》随意玩味侵害和受害的主题。
The gallery's grand scale and high ceilings do make it seem ideal for the shocking elements of Ms Ono's multimedia installation "Das Gift", which toys with themes of aggression and victimhood.
SAS1064是子卡，SAS1064E是这个blade的板上控制器。
SAS1064 is the daughter card, SAS1064E the onboard controller for this blade.
SAS1064是子卡，SAS1064E是这个blade的板上控制器。
SAS1064 is the daughter card, SAS1064E the onboard controller for this blade.
应用推荐