它既可做计时器，又可按预编程序进行多路控制。
The utility model not only can be used as a timer, but also can control in multi-path according to a pre-program.
设计一种以串行输入为基础，串并混合方式输出的多路控制系统。
A multiplex control system based on serial entry and output in series-parallel mixed mode is designed.
文章针对目前医院病房照明灯不合理的控制方法，提出了一种由集成电路组成的多路控制器，使得每个床位都能开关室内照明灯；
According to the unreasonable lighting control for hospital wards, a new type of multi-channel controller with IC was proposed, which makes the light in the room switched by each bed.
因此，在多路模式中，hpmcount和hpmstat控制pmc，让它们在不同的时间片中轮流收集不同的事件组。
So, in multiplexing mode, hpmcount and hpmstat control the PMCs to collect events of different event groups in different time slices in turn.
它通过将入站的连接和事务分配给代理，而控制连接到代理的多路复用。
It controls the multiplexing of connections to agents by dispatching incoming connections and transactions to agents.
像通过多路复用(放在不同的位置)控制文件使数据库免疫、使用联机重做日志和归档重做日志这样的步骤，都是避免单点故障所必需的。
Steps such as immunizing ther database by multiplexing (putting in different locations) control files, using online redo logs and archiving redo logs are necessary to avoid a single point of failure.
本系统可以实现多路温度信号采集与显示，可以使用按键来设置温度限定值，通过进行温度数据的运算处理，发出控制信号达到控制蜂鸣器和继电器的目的。
The system achieves multi-channel temperature signal acquisition and control. Temperature limit is set by keyboard. The buzzer and relay are controlled by MCU.
从丢失的多路复用控制文件成员中进行恢复。
Recovering from the loss of a multiplexed control file member.
在设计中，以TL 494作为PWM产生电路输出控制信号，控制开关管的导通状况，在半桥反激式输出的基础上实现了电源的多路输出。
In the design, to produce circuit TL494 as a PWM output control signals, control of the on-switch situation, the half-bridge flyback output on the basis of the power of multi-output.
本文提出了一种智能时控开关的设计方法，该智能时控开关利用单片机中的定时器、IO接口、中断系统等资源，能根据时刻信息对多路开关进行控制。
This paper proposes a method of intelligent time-control switch design, which USES the SCM timer, IO interface, interrupt system, and other resources to control the multi-channel switch.
介绍了多路温度集中控制系统的结构、设备的选购及安装调试过程。
The structure, selective purchasing, installation and debugging of the multiplex temperature centralized control system were introduced.
介绍了一种用单片机控制的微秒级多路时序信号发生器的实现方法。
A new method of microsecond timing generator controlled by microprocessor is introduced in this article.
以某一视频采集卡为例，实现了多路视频信号在微机上的实时处理和控制，同时给出了视频流的显示、录制和回放方法。
Using microcomputer with video-capture CARDS, multi-video signal is controled and gathered, methods of obtain video-data stream is found include video display, record and replay.
提出了一种利用计算机的USB接口对多路脉冲治疗仪的连接与控制的设计方法。
A design in which the multiplex pulse therapeutic instrument is controlled by the computer via USB interface is proposed.
本文叙述了光纤传感多路收集控制器的基木构成及其基本原理。
This paper describes the structure and basic principle of the optical fiber sensing multi-route accumlating controller.
本文介绍了一种用MCS-51单片机控制的交换机多路外线自动接续装置。
This paper introduces an automatic multi-switch equipment controlled by the MCS-51 microcomputer on the crossbar exchange trunk line.
通过对电液比例多路阀进行负载敏感控制，实现泵和负载之间的功率匹配，显著提高系统效率。
Electro-hydraulic proportional sectional valves are realized with load sensing control, and the pump output power is adaptive to load, the system effectiveness is highly enhanced.
它能实现开关量和模拟量的多路循环检测与控制，使得复杂的检测与控制工作变得简单而且迅速。
It can realize detection and control of multiple recurrences of switching values and analog quantities and make the complex detection and control handy and rapid.
控制系统除了实现对仪器的时序控制、监控其运行状态外，还要对当前反应杯的多路模拟信号进行实时数据采集。
The control system not only realizes the scheduling control and detects the status of instrument, but also collects data of many analog signals of current cuvette.
如果做进一步的研究可将该控制方法应用于多路口的区域交通控制，有较强的实用性和推广价值。
The controlling method which have stronger practicability and value to popularize can be used to control the area traffic control if we do further research.
总线控制协议是高速多路串行数据总线的关键，它决定了多路串行数据总线的实时响应能力以及在高负载和低负载情况下的串行数据总线的特性。
Bus control protocol is the key or high rate multiplex data bus. The capacity of real—time responseness of multiplex data bus and properties in high and low load are decided by the protocol.
控制系统除了实现对仪器的实时操作、监控其运行状态外，还要对当前反应杯的多路模拟信号进行实时数据采集。
The control system not only realizes the real-time operation and detects the status of instrument, but also collects data of many analog signals of response cup.
模拟通道用多路开关来控制。
并通过FPGA设计的数字比较器，同步产生多路PWM电流波形，实现对四相步进电动机转角进行均匀细分控制。
The digital comparator designed with FPGA generates several PWM current waveform synchronously, to realize the step angles even division control for four-phase stepping motor.
本文介绍了基于单片机实现多路开关量控制系统，用于机械原理实验室机构陈列柜演示系统，并用ISD4004系列语音芯片构成语音解说系统。
This paper introduces a switch signal control system based on MCU, which has been used in a mechanism demonstrated system. This system USES ISD4004 series chip to form a voice system.
最后，阐述了一种测试调度的控制策略，使得多路转换器控制输入最少。
Finally, a control scheme during test scheduling is presented, which minimizes the number of extra controllable inputs.
根据高频机箱中受控对象的使用要求，采用AT 89 C52为核心电路，设计了多路电压量输出控制器。
According to usage request of controlled objects in high frequency box, adopt AT89C52 for the core electric circuit, designed multiplex voltage output controller.
详细讨论了在舞台控制系统中利用DSP实现多主式控制通信，采用多路并行计数器解决脉冲丢失，多路同时请求下的DSP控制以及利用DSP方便地实现对电机运动控制。
This system adapt to multi - channels counter solute the pulse' s losing , DSP control which multi - channels reediest at the same time and the convenient realization of motor control .
本文介绍一种用于多路通信控制系统的微型计算机。
The text introduces a kind of microcomputer for multiple communication control system.
本文介绍一种用于多路通信控制系统的微型计算机。
The text introduces a kind of microcomputer for multiple communication control system.
应用推荐