应用齿顶整圆弧滚刀是提高齿轮弯曲疲劳强度的有效措施之一。
Full radius hob on tooth tip is one of the effective measures by increasing gear tooth bending strength.
并且证明，法面双圆弧齿轮的每一段端面齿廓都是对应椭圆曲线段在相对运动中的包络曲线。
Moreover, the extreme shape of the normal double circle gearing proves to be the involved curve of the corresponding ellipse.
计算分析认为，双圆弧齿轮的啮合点分布情况是齿轮的轴向周节、同一轮齿上两啮合点在轴向的距离和齿轮的有效宽度的函数。
Analysis shows that the distribution of meshing points is a function of the axial circular pitch, the axial space of two meshing points on a tooth and the effective width of the gear.
1971年起，我们首先在2400马力客货轮中采用单圆弧齿轮（不必磨齿）代替渐开线齿轮，使用到现在情况良好。
Early in 1971, we installed an experimental single circular-arc-profile gear in a 2400Hp pass- enger-cargo ship instead of an involute gear for the first time.
为此，郑州机械研究所针对低速重载齿轮传动领域设计了ZY-1型硬齿面双圆弧齿轮齿形。
Aiming at heavy duty and low speed gear transmission, Zheng Zhou Research Institute of Mechanical Engineering puts forwards ZY-1 case- hardened double-circular-arc gear.
设计的新型三环减速器主要由圆弧齿同步齿形带、小带轮、大带轮、曲柄轴、传动环板、输出轴、外齿轮和箱体等组成。
Newly developed three ring gear reducer is comprised of synchronous belt, big and small pulleys, crankshaft, drive ring plate, output shaft, external gear and case.
然而，我国对硬齿面双圆弧齿轮传动承载能力及可靠性的研究尚属起步。
However, research on loading capacity and reliability of this kind gear is still at initial stage.
本文用回归分析法求得了GB12759—91型双圆弧齿轮的齿腰应力的计算公式。
A formula is given to calculate the stress in tooth middle of GB12759-91 double circular-arc gear via regression analysis in this paper.
用有限元方法，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算。通过应力计算结果的分析，得出了凸、凹两齿侧应力沿齿长的分布规律。
Through the calculation of the finite element method(FEM) models for double circular arc profile spiral bevel gear, the stress changing pattern along the length of the tooth is obtained.
当前，齿顶整圆弧滚刀广泛应用于重型汽车变速器齿轮的生产中。
At present, full radius hob is used extensively for heavy transmission gear production.
计算结果表明，准端面圆弧齿轮基本上是沿齿高方向等强度分布，优于法面圆弧齿轮。
Computing result indicates that quasi transverse circular arc gear is basically equal on strength distributing along tooth depth direction and it is superior to normal plane circular arc gear.
双圆弧弧齿锥齿轮是将点啮合制圆弧齿轮传动形式运用到锥齿轮上的成功例子。
Its basic gear tooth profile is double circular arc spiral bevel gear tooth profile.
论述波式滚动活齿传动内齿轮齿廓曲线的两种选择：内摆线的等距曲线、密切圆弧曲线的理论成因。
The text introduces the two choices of inner gear profile curve of the rolling gear drive and the theoretical reasons of the equidistance curve of inner cycloid and the close an; curve.
双圆弧齿轮齿端修形是减小啮入冲击、降低传动噪声、避免齿端崩角、提高使用寿命的有效措施。
The tooth end relief is an effective process for double circular arc gear to lighten the shock, lower the meshing noise, and prevent the tooth end from breakage, so as to prolong the service life.
论文工作为今后双圆弧弧齿锥齿轮的进一步研究及推广应用提供了参考依据。
This paper provides reference for later research and application of double-circular-arc spiral bevel gears.
实例计算表明，“错齿”对提高双圆弧人字齿轮强度和降低噪声有影响。
Calculations show that, by applying interlocking teeth, the strength of the gear may be improved and the working noise may be reduced.
传动部分是渐开线齿轮，工作部分可采用不同的工作面，如圆柱外圆面或圆弧形齿或渐开线齿轮齿顶修圆。
The transmission part is an involute gear, and the working part can adopt different working faces, such as a cylinder excircle face, a circular arc tooth or an involutes tooth gear top cavetto.
并根据相关文献给出ZY - 1型双圆弧齿轮基本齿廓的详细参数取值表。
And in accordance with the relevant literature, the detailed parameters table of the ZY-1 type double-circular-arc gear basic tooth profile is given.
用同一双面刀盘在格里生机床上成功地切出了等高齿双圆弧弧齿锥齿轮副。
By using the same alternate blade cutter, bi-arc spiral bevel gear pair with equal-height tooth can be produced on the Gleason machine.
叙述了准端面双圆弧齿轮的形成原理，推导了这种齿轮的通用齿面方程。
Theory of quasi-circular-arc gear's shaping is discussed in this paper, and its common tooth-surface equation is developed.
本文通过八对圆弧齿线圆柱齿轮的运转接触疲劳试验，得到了45钢正火齿轮的接触疲劳极限应力框图，可供圆弧齿线圆柱齿轮传动的接触强度计算参考使用。
In this paper, contact endurance limit diagram of 45 normalizing gear is obtained from contact fatigue teste on 8 pairs of CATT gears. It is worthy reference for a calculation of gear design.
用有限元方法 ，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算 。
The analysis of adjusting errors on processing double circular arc profile bevel gear;
首次采用线图法分析了其啮合过程，建立了双圆弧齿廓弧齿锥齿轮重合度、多点接触系数和多对齿接触系数计算方法；
The meshing process is analyzed using line graph method firstly, calculation methods of the contact ration, multi-point contact coefficient and multi-pair contact coefficient are established;
首次采用线图法分析了其啮合过程，建立了双圆弧齿廓弧齿锥齿轮重合度、多点接触系数和多对齿接触系数计算方法；
The meshing process is analyzed using line graph method firstly, calculation methods of the contact ration, multi-point contact coefficient and multi-pair contact coefficient are established;
应用推荐