变速器轴承外壳是汽车的重要零件。
变速器轴承外壳是汽车的重要零件。
摘要变速器轴承外壳是汽车的重要零件。
同时得到了整个运行过程中抬轮器轴承的最高温度值。
The highest temperature of wheel shaft in whole test process was also obtained.
设计的配重装置可大大减缓变速器轴承处支撑反力的波动。
The designed counterweight device can largely reduce the fluctuation of reacting force on the bearing of gear-box.
换向器端轴头装有测速齿盘，换向器轴承盖留有轴承温度传感器安装口。
Frame is a press-formed welded fabrication and hugging bearing or bush structure; Speed gear plate is mounted on shaft end of commutator.
参考同类车型的结构布置，本设计变速器轴承按国家标准选择圆柱滚子轴承。
It referenced the structural arrangement of similar vehicle, this design transmission bearing according to national standard that choose the cylindrical roller bearing.
介绍了一种高速发动机离合器轴承试验机测控系统的组成、工作原理和控制算法。
The composition, working principle and control arithmetic of a high - speed aviation engine clutch bearing test machine is introduced.
为了是中国汽车产业同步增长，公司已成为汽车离合器轴承和涨紧轮轴承最专业的供应商。
For it is a simultaneous increase in China's auto industry, the company has become an automobile clutch tensioner pulley bearings and bearing the most professional suppliers.
滚针离合器轴承是可单向传递轴和轴承座之间的扭矩，而反方向允许自由转动的一种复合功能轴承。
The needle roller clutch bearing is a kind of compound function bearing which transmits torque between the shaft and housing in one direction and allows free overrun in the opposite direction.
某带行星齿轮减速器的发电机组在满负荷额定转速工况下，出现减速器轴承及发电机后轴承处横向振动偏大的故障现象。
Under the condition of rated load and rated speed operation of a generator set, over-vibration phenomena appeared in the planetary gearbox's bearing and the rear bearing of the generator.
介绍了为提高铁道车辆用轴承的安全性、可靠性并延长其寿命而开发的塑料保持架、搭载传感器轴承，以及车辆运动仿真试验机。
Described are the plastic cage, sensor-carrying bearings and rolling stock motion simulation tester developed for safety, reliability and prolonging the service life of bearings for rolling stock.
2005年，杜克大学工程系研究生同时也是一位极具热情的吉他手，莱尔斯，用胶合板、两个螺旋、一个滑板轴承和一些备用吉他部件制作了他的第一个调音器。
In 2005, Lyles, a Duke University engineering graduate and an avid guitarist, built his first tuner out of plywood, two screws, a skateboard bearing and some spare guitar parts.
在这些轴承中，有轴角编码器，它们感受到了外面的框的转动，来保持这个东西，指向相同的方向。
And in these bearings here are shaft encoders, and they sense that the rotation that the outer housing makes in order to keep this thing pointing at the same direction.
诸如此类的复杂机器遍身是令人不解的阀门、过滤器、管道、软管、耦合器、轴承、开关、量表、仪表和传感器。
Complex machines like this are riddled with valves, filters, tubes, hoses, couplings, bearings, switches, gauges, meters and sensors.
在此基础上，研究了用球结构支持向量机作分类器，对滚动轴承内圈故障的劣化程度进行识别的理论和方法。
Basing on these, study theory and method of using Sphere-structured Support Vector Machines to recognize the roll bearing inside track's fault deterioration extent.
单向、双向压力球轴承保持架一般采用钢板冲压成型，大尺寸或特殊用处的轴承则采用黄铜或软钢车削保持器。
One-way, two-way pressure ball bearing cage generally use steel stamping molding, large size or special use of the bearings are made of brass or mild steel turning cage.
在轴承中的轴必须经过检测，轴可以由离合器启动，或用闸来停止。
The shaft must test in bearings, may be started by a clutch or stopped with a brake.
该指南杆和轴承系统的负载，同时支持的滚珠丝杠驱动器的负载。
The guide rod and bearing system support the load while the ball screw drives the load.
由控制器控制的轴承现在应该表现得更好。
Bearings controlled by the controller should now behave better.
分析和研究了磁力轴承控制器控制算法。
Secondly, analysis and research of control arithmetic of magnetic bearing .
基于减速器的齿轮、轴、轴承、及其校核，文章给出了设计和计算。
Based on the gear reducer, shaft, bearings, and checking, the article gives the design and calculation.
自从大电机式轴承整个编码器游戏机，该单位可以容忍相当大轴的运动。
Since the entire encoder rides on large motor style bearings, the unit can tolerate considerable shaft movement.
本文介绍控制液压轴承车床的可编程控制器的软硬件。
The paper introduces the hardware and the software of PC for hydraulic bearing lathe.
风机的轴承，油封及消声器，叶片等属于消耗品，故有一定寿命，需定期更换。
The bearing, oil seal, silencer and leaf of the fan are wearing parts with limited life and should be changed periodically.
磁悬浮轴承的控制器设计通常是在平衡点附近进行线性化，按照线性理论设计线性控制器。
The usual design of the magnetic controller always linearizes around the balance point and bases on the linear system theory to design the linear controller.
在磁力轴承系统的研究中，控制器的设计是其中至关重要的一环。
The most important research field of AMB focuses on the research on the controller.
我建议他使用轴承拆卸器进行拆卸，这件事发生在周一。
I suggested he would be better served using a bearing puller. That was Monday.
弹性轴承、中心部件和缓冲器安装在悬臂固定在桥上的部分。
The elastomeric bearing, the centering member and the buffers are mounted on a cantilever on the fixed part of the bridge.
弹性轴承、中心部件和缓冲器安装在悬臂固定在桥上的部分。
The elastomeric bearing, the centering member and the buffers are mounted on a cantilever on the fixed part of the bridge.
应用推荐