它既可以用专用喷涂设备喷涂施工，也可以用手工涂刮施工。
The paint can not only carry out spray construction by using special spraying equipment but also can carry out spray scraping construction by hands.
提出了如何进行操作与维护和故障排除以及喷涂施工时的注意事项。
The operation, maintenance and trouble - shooting are stated, and safety working, environment, working protection and cautious items are presented.
无空气喷涂在大面积涂装的领域内，代替了传统的喷涂施工。主要原因如下。
Airless spraying had replaced conventional spraying for painting of large surfaces for the following reasons.
通过现场试验，优化了聚氨酯泡沫原料配比，确定了合理的聚氨酯泡沫喷涂施工工艺。
Through field test, polyurethane foam raw material match has been optimized & reasonable polyurethane foam spray construction technology has been determined.
如果如使用喷雾器喷涂，最好戴上口罩并在通风较好的空旷地上进行，不建议在室内喷涂施工。
If use the spray, had better put on mouth-muffle in the airiness open space, don't suggest spray indoors.
对喷涂施工中产生的问题及控制重点采取了相应的有效措施。确保了喷涂的施工质量达到技术要求。
As to the problems occurred and main control points during gunning, the relevant effective measures are taken to ensure the construction quality of gunning reaching the technical requirement.
如果喷涂施工是在狭小舱室内等有限空间进行时，必须佩戴通风面罩，以空压机不断送入经过滤处理的新鲜空气，以供操作者呼吸之用。
If spraying application is carried out in a limited place like narrow booth, the operator must wear a ventilated mask with an air compressor for feeding filtrated fresh air.
施工方法：辊涂、刷涂或喷涂。
讨论了喷涂氨基锤纹漆的工艺参数、施工要点、漆膜质量及产生漆膜弊病的原因。
Process parameters, application essentials, film quality and reasons causing the film objections in spraying amino hammer paint are discussed.
螺旋桨喷涂有机硅防污涂料施工时要注意些什么？
Whatshould be paid attention to when the propeller is sprayed with silicone antifouling painting?
喷涂聚脲(SPUA)技术是采用专用设备，现场喷涂工艺施工的一种新技术。
A technique of spraying polyurea (SPUA) is a new technique using the special equipments and in situ spraying process.
聚氨酯材料组合、售，现场喷涂发泡施工。
PU material composition, marketing, on-site spraying foam construction.
介绍喷涂聚脲弹性体的力学性能，耐介质性、低温韧性、耐老化性、附着力及其施工。
This paper introduces mechanical property, medium resistance, low temperature toughness, age resistance, adhesive tension and construction of sprayed polyurea elastomer.
耐火纤维喷涂是纤维机械化施工的一种新工艺。
The spray coating is a new technology for fiber mechanical construction.
施工方案：喷砂处理，化学处理，喷涂高分子防腐材料。
Construction scheme: sand blasting, chemical treatment, spray polymer anticorrosive material.
以快速喷涂作业，工程快速，施工安全简单。
The quick spray makes the project quick, construction safe and simple.
避免在阴雨季节、空气湿度高的天气进行施工。尤其是在湿度高的天气进行喷涂易造成涂膜发白现象。
In the rainy season 6, avoid, air humidity high weather for construction. Especially in high humidity weather for spraying easy cause film white phenomenon.
喷涂衬里适用于旧炉衬改造，可简化设计和施工。
This spray lining, simple in engineering and construction, was specially applicable for the revamp of the existing furnace.
前者是指在合成材料的施工在非固体的形式存在，如胶粘剂、表面喷涂材料；
The former refers to exist in a non solid form in the construction of synthetic materials, such as adhesive, surface spray materials;
施工的涂料应采用适合的特定喷涂方法。
Paint should be applied with a proper and specified spraying method.
喷涂聚脲弹性体技术是一种新型无溶剂、无污染的绿色施工技术。
Spray Polyurea Elastic(SPUA) is new-fashioned technology of non-solvent and non-pollution adverse effect.
介绍耐火纤维及其制品的特性、分类及几种施工工艺，并着重介绍耐火纤维喷涂技术。
To introduce the characteristics, classification and some kinds of construction technologies of refractory fibre and its products. Refractory fibre spraying technology is emphatically introduced.
喷涂聚脲弹性体技术是一种新型无溶剂、无污染的绿色施工技术。
Spray of Polyurea Elastomer (SPUA) is a newly developed and healthy technology of water proofing without resolvent and pollution.
介绍了热喷涂锌不锈钢阶梯涂层的施工工艺及工程应用情况。
The technology and application of zinc stainless steel hierarchical coating by thermal spraying in hydro steel structure are introduced.
超长耐候性、优良抗污性、极低VOC排放、绿色环保；良好施工性，可以滚、刷、喷或无空气喷涂；超长使用寿命，极低维修费用，经济效益好。
Long weather resistance, excellent stain resistance, low VOC emissions, green; good site, and it can roll, brush, spray or airless spray; long life, low maintenance cost, good economic returns.
介绍了一种可在室温下用刷涂、喷涂、浇注等方法施工和固化的聚氨酯弹性体，并介绍了所用原料、合成方法、主要性能等。
Polyurethane elastomer suitable for brushing, spraying and pouring at ambient temperature is described. The raw materials, synthesis and properties are presented also.
标线施工机械系列有：手推式、自行式、乘驾式和车载式常温标线喷涂机。
Marking construction machinery series: hand push type, type, type and vehicle ride type normal temperature marking spraying machine.
如按iso 834曲线升温，耐火性能达到3h，一般涂料涂层厚度约需20 ~30mm；由于涂层较厚，需要多次喷涂，施工困难。
E. g. by ISO 834 curve thawing, fireproof performance reach 3h, general coating thickness need about 20 ~ 30 mm, Due to the coating thicker, requiring multiple coating, construction difficulties.
阐述了冷库现场喷涂聚氨酯施工作业中对原材料、施工队伍、施工工艺等方面的要求和建议。
The thesis is description of requirements and suggestions for raw material, construction staff, and construction technology during field plating polyurethane plastic foam on job site of cold storage.
介绍了单头空气喷枪、空气静电喷枪、高速旋杯式静电喷枪各自的工作原理、施工特点及影响喷涂质量的工艺参数。
The working principles, characteristics and process parameters of single head air spray gun, air electrostatic spray gun and high-speed rotated cup type electrostatic spray gun were introduced.
应用推荐