物体受力分析是研究质点动力学问题的关键。
文章重点介绍合拢段受力分析与劲性骨架设计。
The article mainly presents the stress analysis and stiff skeleton design at the closure sector.
物体的受力分析，是静力学研究中的重要技能。
Analyzing forces loaded of the object is an important technique in the static mechanics.
初始预应力分布的计算是双层索结构受力分析的基础。
The calculating of initial prestress distribution is basic and important for analyzing of double-layer cable structure.
介绍了该桥的总体布置、结构设计、受力分析及施工概况。
In this paper, the overall layout, structural design, stress analysis and construction of the Bridge are dealt with.
本文主要介绍了埋砂法恒定加速度试验时元器件的受力分析。
In this paper, we analyzed the sample forced by inter-sand method of centrifugal test.
对钻头在钻进过程中的受力分析是准确预测钻头轨迹的基础。
The mechanical analysis of the bit in the process of drilling is the bas- is of bit trajectory prediction.
分析了制动装置的工作原理，并对其结构做了受力分析和优化。
Analyse the working principle of the brake device in the passage, and force analysis and optimization for the structure.
第一次得到一幅完整的人体牙齿咀嚼过程的受力分析和运动状况。
It is the first time to get an entire measurement of the teeth physiological loads and movement status.
文中阐述了该封闭传动的特点，传动比计算，受力分析和效率计算。
First the major Characteristics of this transmission, calculation of ratio, analysis of forced and calculation of efficiency are given.
该项研究对其它斜式泵的内部流态及受力分析也是一个很好的借鉴。
More, this study was useful for the inner flow field and force analysis of other slantwise pumps.
通过对鼓式制动器的受力分析，建立了其关键受力部件的力学模型。
This article analysed the loads of the drum brake and built the key brake's mechanical model.
本文对一种新型的传动——波齿传动进行了受力分析和传动效率计算。
The forces and efficiency analyses of the wave gear transmission are presented in this paper.
本文采用组合变形的分析方法，对锥体连接钎头工作时进行受力分析；
Using the combined deformation analysis method, the author mache an analysis of tapered bit forced in operating.
在此基础上进行了对振动筛的运动分析，筛面上谷物的运动及受力分析。
On these basic the movement of vibration sieve were analyzed, the movement and the force of cereal on sieve were analyzed.
本文介绍了轴销剪切式称重传感器的结构与特点，受力分析与理论计算。
This article introduces structure, characteristic, stress analysis and theoretical calculation of shaft pin cutting type load cell.
文中通过颗粒的受力分析解释了这一具有重要理论与实践意义的模拟结果。
This is of significance in both theory and practice and is explained by analyzing the action forces between particles.
并对固定桥的连接体部分进行受力分析，寻找最合理的连接体的设计方案。
The stress of the connector of the bridge was analyzed to find the best design of the connector.
结合驱动轮参数对驱动轮进行受力分析，推导出该机器人驱动轮的驱动力矩。
The forces of the driving wheels are analyzed using parameters of the wheels and the driving torque is deduced.
由于箱梁结构广泛应用于桥梁建设中，而传统的受力分析方法存有较大的误差。
For box girder structure which is applied extensively in bridge construction, the traditional analysis method of load is of comparatively bigger error.
以连续梁模型作为曲轴受力分析的基础，分析了平衡重对曲轴所受弯矩的影响。
On the basis of continuous beam model the effect of fitting counterweights on the bending moment of crankshaft was analysed.
本文详细介绍了槽钢锁口一次冲压成型模具结构的特殊性，定位方式及受力分析。
This paper introduces the construction speciality, positioning method and stress analysis on primary pressing model of the bar cut.
索穹顶结构是大变形柔性组合结构，其受力分析属于几何非线性问题，求解较复杂。
Cable dome is a large deformation composite structure consisted of flexible cables. Its analysis is a geometric nonlinear problem and is difficult in its solution.
通过对静电封接结构的受力分析，建立了静电封接后弹性膜片的热失配应力数学模型。
The stress of anodic bonding is analysed and the math model of no match thermal stress about anodic bonded elastic diaphragm is built.
通过对电火花线切割机床在加工过程中的特殊受力分析，给出步进电机的匹配选择方法。
This article introduced the matching selection of step motor for wire-cut electric discharge machine by analyzing the special stress of the machine.
具体包括：确定本起吊设备的工作级别、动力装置的各部分的设计计算和支架的受力分析。
Specifically including: determining the level of the work lifting equipment, power devices and components in the design of the structure Analysis of Edge.
详细介绍了铣刀的设计方法，包括参数设计与建模、受力分析与计算、有限元分析与校正。
The cutter's design method, including parameter design and modeling, stress analysis and calculating, finite element analysis and correcting was introduced in detail.
在对移动机构的静态和动态进行受力分析的基础上，确定了单个磁性吸附块的最小吸力参数。
On the basis of the static and dynamic stress analysis about the traveling mechanism, the minimum suction parameter of the single magnetic adsorbing block was determined.
本文采用材料力学中梁的受力分析方法给出了这类容器中支座反力和最大轴向弯矩的计算方程。
In this paper, the beam analysis method was applied to derive the equations for calculating the support forces and maximum axial moments acting on the vessels.
通过对张力控制结构作定量的受力分析与计算，设计新型恒张力控制结构和工字轮锁紧气动顶尖。
Through quantitative force analysis and calculation of tensile control structure, new constant tensile control structure and locking pneumatic finial of spool are designed.
应用推荐