导航员：请报告你的高度及位置。
顶棍孔尺寸及位置是否正确?。
本文讨论了转变点个数及位置的检测问题。
In this paper the detection of the number and locations of change points is discussed.
本文介绍了提高部件尺寸及位置精度的几个途径。
Several approaches to increase the size and position precision of Flyblack rest parts are introduced.
着重介绍了它的机械结构及位置调整运动控制算法。
This article emphasizes the mechanism, position adjusting and motion controlling algorithm.
介绍了某中厚板厂轧机的机械特性及位置控制系统。
Mechanism characteristics and position control system of a heavy and medium plate mill are introduced.
研究了止音毡压力及位置对钢琴琴弦阻尼作用的影响。
The influence of damper with different pressures and positions on damp vibration of piano string is studied.
采用增量式编码器，通过速度及位置信号进行双闭环控制。
Double closed loop control is implemented with increment encoder through signal of speed and position.
轴承座分 别将两根执行丝杆及位置传动丝杆固定在底座上；
By bearing seat two executing screw shafts and position driving screw shafts are set on the base plate.
人脸检测就是判断被检图像中的人脸，并确定其大小及位置。
Face detection is to determine the size and location of a human face in an image which is being detected.
根据声明这些变量的方式及位置，这三类变量有以下五种作用域。
There are five types of scope that these three types of variables can have, depending on how and where they are declared.
交流伺服系统检测电路由电流、电压、转速及位置检测电路组成。
Test circuit of AC servo system was composed of current test circuit, voltage test circuit, speed and position test circuit.
结果：胎儿外耳在孕20周以后即可清晰显示其形态、大小及位置。
Results: the morphology, the size and the lie of the fetal external ear could be clearly seen after 20 week pregnancy.
绿色的闪光也出现在太阳升起时，但是在合适的时机及位置才能观察到。
A green flash is also visible for a rising Sun, but takes better timing to spot.
本文对13例人心标本房室结和房室束的形态及位置，作了连续切片观察。
The morphology and position of the AV node and AV bundle were observed in 13 human hearts with serial sections.
跟踪生产线上静电的控制情况，对静电棒清洁状况及位置等进行日常的检查。
Track static electricity control status on production line, conduct regular check for E-static bar cleaning status & installation location.
现场测量：设计师到施工现场实地测量，包括房间墙壁面积、门窗暖气面积及位置。
The spot measurement: the designer goes to the spot to measure the area and position of the room wall, heating system, doors and Windows.
讨论了载体姿态及位置均不受控制的自由漂浮双臂空间机器人系统的轨迹控制问题。
The paper studies the nonlinear feedback control problem of free-floating dual-arm space robot systems.
文章介绍利用超声波数据采集系统采集的数据，实现对缺陷的大小及位置的精确定量。
This paper introduces the quantitative evaluation of precise size and position of flaw by using data collected by ultrasonic data acquisition system.
结果表明，苯环上取代基的种类及位置对化合物分子的共轭体系及共平面程度有较大影响。
The results indicate that the kind and position of the substituents in aniline ring greatly affected the conjugation system and coplanarity of the products.
一般机载光电跟踪测量系统用来在飞机上实施对地面目标或空间目标的精确角度及位置的测量。
Generally, APSSE is used to implement the measuring of the precise Angle and position of ground goal or space goal.
接收波则综合携带了损伤介质内部特性信息，可通过这些信息研究损失介质损坏的程度及位置。
The internal characteristic information of the damaged media was carried by the received wave, the damaged degree and location of the damaged media can be studied by these information.
求出由轴向振动引起的最大动应力的大小及位置，进而对振动量与最大动应力的关系进行剖析。
The size and location of the maximum dynamic stress induced with axial vibration were found, the relation between the vibration quantity and the maximum dynamic stress was analyzed.
多极无刷旋转变压器采用乘法解调及信号合成得到适合开关磁阻电机驱动用的速度及位置信号。
The multiple brushless resolver uses multiplication demodulation and signal composition to achieve rate and position signals proper for driving switch reluctance motor.
目的：对周边视野检查常常是根据临床经验判断病眼周边视野病变的大小及位置，存在主观影响。
AIM peripheral visual field test is often to estimate the size and location of pathological peripheral visual field according to clinical experience which has subjective effect.
主要结论如下：(1)北半球及各分区极涡的面积、强度及位置有着很明显的年际及年代际变化。
The main results show as following: (1) There is obvious inter-annual and inter-decadal variation for polar vortex, including the variation of area, intensity and location.
作者用模型选择的方法提出了一种程序以估计转变点的个数及位置，然后建立了这些程序的强相合性。
The authors propose some procedure for estimating the number and locations of change points within the framework of model selection, and establish the strong consistency of these procedures.
本文介绍了提高部件尺寸及位置精度的几个途径。采取相关措施后，其精度达到或超过进口件的水平。
Several approaches to increase the size and position precision of Flyblack rest parts are introduced. Taking some relative measures, the precision would surpass that of imported parts.
本文介绍了提高部件尺寸及位置精度的几个途径。采取相关措施后，其精度达到或超过进口件的水平。
Several approaches to increase the size and position precision of Flyblack rest parts are introduced. Taking some relative measures, the precision would surpass that of imported parts.
应用推荐