沿着这条红色路径，你从一个等压过程开始，以一个等温过程结束。
Along this red path, you start with an isobaric process and end with an isothermal process.
等容过程优于等压过程。
与等压和等压过程中的吸附床的SCP相比，等压过程更好。
Compared to the SCP of the adsorption bed under isochoric and isobaric process, the isochoric process is better.
所以上面这条红色的路径，就是个等压过程。
So, this path right here from this top red path is an isobaric process.
对不同工艺参数下的滚珠旋压过程进行了模拟。
Different technological parameters of ball spinning are simulated.
同样的，它由两个等温过程和两个等压过程组成。
Similarly, it is composed of the two isothermal and two isobaric processes.
本实用新型具有可自动复位、泄压过程柔和的优点。
The utility model has the advantages of automatic reset and flexible pressure release process.
比较全面而准确地描述了金属塑压过程三维流动的情况。
The three-dimensional flow in metal plastic compression process are described more completely and accurately.
这是一个等式，这是个恒压过程，这项等于零，这意味着。
This is just an equality. I have a constant pressure dH process. This term here is equal to zero.
着重介绍了水压过程增压补进水计算和高压水系统的设计。
This article emphasizes calculation of boosting and water supply and design of high pressure water system.
对铜母线连续挤压过程的几何模型进行简化，基于MSC。
By simplifying the geometry model of the copper bus bar continuous extrusion process, based on a new metal forming simulation package, MSC.
通过对冷冲压过程的实地观察分析，找准了裂纹产生的原因。
By observing and analyzing cold punching process at the factory, the cause of the crack formation was found.
一半的实验组减压过程高考撤除加压棒及30分钟恢复时间。
In half the experimental groups, a decompression phase consisting of probe withdrawal and 30 minutes of recovery was also applied.
实验研究了液态浸渗后直接挤压过程模具与坯料内部的温度变化。
The temperatures at different positions inside the die and the extruded-billet during extrusion directly following liquid infiltration were experimentally investigated.
它与一般的低密度聚乙烯不同，后者采用较不方便的高压过程生产。
This is in contrast to conventional LDPE which is produced by the somewhat less convenient high pressure process.
推进剂的燃烧特性及喷管堵盖打开压强对点火升压过程有较大影响。
Propellant property and nozzle closure opening pressure have an important effect on the ignition transient.
供热系统水压过程是一个耦合的、变参数的、非线性的多变量过程。
Hydraulic pressure process in heating system is coupling, parameter varying, nonlinear, multi-variables process.
煤气混合加压过程的控制目标是要保证送出煤气的热值与压力稳定。
The control target of the mixing and pressurizing of the gas is to ensure the stability of the calorific value and pressure of the gas.
同时揭示了内不可逆性及等压过程高低温比值对系统优化性能的影响。
The influences of the internal irreversibility and the high-low temperature ratio in isobaric process on the optimal performance of the system are revealed.
这个过程是主动运动，而不是由血液的流体静力压所致的被动挤压过程。
The process is one of active motility rather than passive extrusion by the hydrostatic pressure of the blood.
利用上限元法(UBET)模拟了圆柱直齿轮径向挤压过程的变形力规律。
Laws of the deformation force during radial extrusion of spur gear are simulated by using UBET.
利用承压砌块模型分析了周期来压过程，并给出了初次来压和周期来压机理。
Periodic weighting was analysed by the bearing wedge model, simultaneity, the mechanics of first weighting and periodic weighting were expounded.
它的特征是进变质与退变质路径近于平行，早期退变质作用为降温、降压过程。
It is characterized by the prograde trajectory is parallel nearly to the segment of retrogression, and the early retrograde metamorphism with coupling of decompression with a temperature decrease.
采用低压过程，齐格勒·纳塔聚合或菲利浦斯公司工艺生产的一种低密度聚乙烯。
A low density polyethylene produced by a low pressure process, by Ziegler-Natta polymerization or by use of the Phillips process.
模型首次直接对影响辊压过程的关键因素即基材材质和辊压条件进行了模拟分析。
The model directly simulate the blade material and rolling conditions, the key factors in rolling process for the first time.
这台机器采用了特殊设计的螺杆和桶，模具和挤压过程，以生产塑料和木材产品。
This machine USES the special designed screw and barrel, die and extrusion process to produce plastic and wood products.
对挤压过程热传递过程分析表明坯料冷却程度与其所处应力状态和保温介质有关。
It shows that the thickness of cooling hard layer is associated with the state of stress and heat preservation material by analyzing the heat transfer principle.
喷丸过程和随后的接触疲劳滚压过程同属在赫兹应力作用下的循环弹塑性应变过程。
Both shot peening and contact rolling belong to the cyclic elastic-plastic deformation process under the action of Hertz stress.
通过对挤压过程压制力和位移曲线的分析，提出了对挤压过程三个阶段的合理划分。
The extrusion is successfully divided into three ideal stages through the analysis on the pressing force and displacement curve in the process of extrusion.
通过对C12200铸锭的切片分析，提出挤压过程含磷类管材表面起泡的新见解。
By the analysis of cut piece of billet C12200, a new view is put forward for tube surface bubble of phosphorous copper in the extrusion.
应用推荐