它是在类似压力锅的一个大的不锈钢锅炉里，放入碱液，加热到300度，压强为0.414兆帕的条件下将尸体溶解掉。
It uses lye, 300-degree heat and 60 pounds of pressure per square inch to destroy bodies in big stainless-steel cylinders that are similar to pressure cookers.
用于固体火箭发动机壳体和工业贮罐的纤维缠绕压力容器，爆破压强是重要的设计参数。
The burst pressure of filament wound pressure vessels which is applied to solid rocket motor case and gas tank in industry is an important design parameter.
利用最大应力强度准则，得到了单一螺旋缠绕及螺旋加环向缠绕圆环压力容器爆破压强的计算式。
According to the maximum stress strength criterion, the burst pressure formula for the single spiral and the spiral with hoop filament-wound toroidal pressure vessel were obtained.
最后，利用所得的解研究了材料的中间主应力效应和拉压强度差效应对厚壁圆筒安定极限压力的影响。
Finally, the influences of the intermediate principal stress and the strength-difference on the shakedown limit pressure of the thick-walled cylinder are investigated by the present solution.
在地球较高层面中的危险的压强点，已即将自行裂开——因为来自于增加的能量的新的压强和压力的集结。
Already dangerous pressure points in the Earth's upper layers are now about to break apart because of new pressure and stress from the increased energy build up.
老式静水压强实验仪存在的问题有：压力调节过程繁琐，容易外溢；
Problems existed with the old hydrostatic pressure tester:Complicated pressure adjustment procedures and easy spill;
由于其激光工作介质是气体，而且激光腔内的压力与外界环境压强相差很大，激光束的输出窗口必须密封。
Because the working media of laser is gas, and the pressure difference between the inner apparatus and environment of laser is large, so the window of output laser beam must be sealed.
研究了连续油管的工作力学特性，建立了连续油管弯曲、抗内压强度和外部挤毁压力、直径增长、纵向伸长及卡点位置分析计算模型。
Mechanical characteristic of ct is studied. The model of bending, internal pressure strength and external collapse strength, diametric growth and stuck-point of ct is established.
第四段：金星大气层密度非常之高，造成的压力相当于3000米海底压强。
Step4 section: Venus atmospheric density is very high and the pressure equivalent to 3000 meters underwater pressure.
不同热压时间、温度、压力对支架孔隙率及抗压强度的影响。
Influence of hot-pressing time, temperature and pressure on the porosity and compressive strength of the scaffold.
侧压力在增大水泥黄土轴向抗压强度方面的贡献是比较小的。
The effect of side-stress to improve cement-loess axial compressive strength is little.
AP所有的气动压力机是一种小型台式压力机，用于小型压力应用。冲压强度从0-1000磅，取决于选择的型号。
The AP all air press system is an ideal compact bench-top press for small precision pressing operations. Pressing forces range from 0-1000 lbs depending on model chosen.
由于瘠性料的抗压强度高于塑性料，从而导致瘠性料的成型压力高于塑性料。
The densification molding pressure of hard brittle material is higher than that of plastic material because of the higher compression strength of hard brittle material.
部分供足砪趾的峰压力、峰压强异常增高，而另有部分供趾的则明显降低甚至缺失；
The peak force and peak pressure greatly increased in some donor great toes, but distinctly decreased, even undetectable for some others.
缩写p【物理学】压力；压强：统一作用于物体表面的力量，用每一单位面积上的压力计量。
Abbr. PPhysics force applied uniformly over a surface, measured as force per unit of area.
提出了通过比较金刚石施加给岩石单位面积的压力与岩石抗压强度来设计金刚石浓度；
The design plan of diamond concentration is submitted by comparing the pressure of rock unit area forcing by diamond with crack strength of rock;
研究成型压力对蒸压灰砂砖抗压强度和耐盐酸腐蚀能力的影响。
In this paper, the effect of molding pressure on the strength and hydrochloric acid stability of autoclaved lime_stone sand brick is studied.
研究了生物质配入量、肥煤配入量、成型压力、 煤料筛分组成、炭化加热速度对型焦抗压强度的影响。
The effect of additive amount of biomass and fat coal, briquetting pressure, coal sizes distribution, heating velocity of the carbonization process on the strength of formed coke were examined.
提出了根据不同污垢的耐压强度极限应力，设计喷咀直径及射流压力的理论方法。
The theory method of designing the diameter of jet nozzle and the water pressure are advanced in the light of the endurance limit stress on the dirt.
从压力到压强的精确转换要求力垂直集中作用在活塞上。同时活塞也不能受到的拉力或压力。
Precise conversion of force to pressure requires the force to act vertically and centred on the piston which must not be exposed to any other forces of thrust or traction.
波纹管随阀杆的升降而伸缩，其最高工作压力取决于波纹管的耐压强度和疲劳强度。
The corrugated pipe expands and contracts along with valve lever's fluctuation, its highest working pressure is decided by corrugated pipe's pressure resistance intensity and the fatigue strength.
而处于研磨阶段时，轴向压力、扭矩和试样弹性模量、黏聚力及内摩擦角有关，与抗压强度无关。
When the sample is at the stage of grinding damage, the axial force and torque are related to the Young? S modulus, cohesion and internal friction Angle except the compression strength.
而处于研磨阶段时，轴向压力、扭矩和试样弹性模量、黏聚力及内摩擦角有关，与抗压强度无关。
When the sample is at the stage of grinding damage, the axial force and torque are related to the Young? S modulus, cohesion and internal friction Angle except the compression strength.
应用推荐