最后对单层厂房抗震研究的方向提出了建议。
Furthermore, gives the suggestion of research problems of single storey mill bu...
可以作为地震区，特别是高烈度区单层厂房柱间支撑设置的一种方案。
This arrangement could be used in those buildings built in seismic zone, especially in zones of higher intensity.
本文研究了单层厂房在地震动作用下屋盖保持完整的非弹性地震反应。
Research work in this paper includes inelastic analysis of earthquake responses of single-story factory buildings with roofs continuing to act as a whole unit under seismic action.
推导出一端有山墙单层厂房在行进的地震波作用下横向地震反应的计算公式。
A formula is derived for calculating the lateral seismic response of 1-storied industrial building with a gable wall at one end under the action of travelling waves.
PARK第一车间：面积约1500平方米、净高9.2米，单层厂房、空间灵活。
D · PARK Workshop: covers 1500 square meters, 9.2 meter high, flexible space.
论文的基本思想和研究方法对于其他类型的单层厂房结构的安全控制也有很大的参考价值。
Moreover the basic idea and research method in this paper offer a important reference to other types of monolayer workshop structure.
除了在炎热的气候条件下，一般说来，如果厂房是单层的，它可以从屋顶很好地采光。
If a factory is of one storey it can usually be well lit from the roof except in hot climates.
标准厂房一般面积在1000——5000，长宽比例适中，单层，7 - 10米高，(行车可选)。
Standard workshop general area in 1000-5000, aspect ratio is moderate, single-layer, 7-10 meters high, (lane optional).
产品广泛应用于大型工业厂房、市、览馆、育馆、代化住宅、公楼等单层及多层建筑群体。
Itsproducts are widely used in industrial workshop, supermarket, exhibition hall, gymnasium, modern residence, office building, tall building, etc.
论文为此针对单层钢结构工业厂房提出了结构可靠性的状态评定方法，为维护、监控规范的制定提供理论依据。
State appraisal method of structure reliability of monolayer steel structure industrial workshops is developed and render academic gist for the establishment of maintenance and monitoring criterion.
针对吊车起重量(Q)在控制单层工业厂房设计中的重要性。
Aiming to the crane load (Q) importance in control single story mill building design.
论文为此针对单层钢结构工业厂房提出了结构可靠性的状态评定方法，为维护、监控规范的制定提供理论依据。
State appraisal method of structure reliability of monolayer steel structure industrial workshops is developed and render academic gist for the establishment of maintenance and.
讨论了桥梁、工业厂房和大型公共建筑中较多采用的单层多跨刚架在移动荷载作用下影响量的计算方法。
The calculation method for the influence quantity is discussed for single-layer multi-span frames under moving load, which are wildly used in Bridges, industrial and public buildings.
厂房可分为两种类型单层的和多层的。
Plant can be divided into two types: single and multi-layer .
结合单层工业厂房的构造特点，将夹层橡胶垫隔震技术引入到单层工业厂房的设计中，并探讨了橡胶垫的减震效果和减震机理。
In this paper, the seismic isolation technique is used in seismic-releasing of the single-storey industrial building by use of laminated rubber bearing as link member between roof and column.
本文提出了关于单层工业厂房横向与纵向刚度实用和简单的计算方法，以供结构设计工作者参考。
A practical and simple method is thus proposed for calculating the transverse and longitudinal stiffness of a single-story workshop and this is for the reference of the structural designers.
除了在炎热的气候条件下，一般说来，如果厂房是单层的，它可以从屋顶很好地采光。
If a factory is of one storey it can usually be well lit from the roof except in hot cli...
本文阐述了长方形网格网架在单层工业厂房屋盖中的合理应用。
This paper expounds the reasonable application of the space trusses with rectangular latticework on the roof of single-storey factory building.
本文介绍一种用现场预制的折叠式V形钢筋混凝土折板作为承重墙和屋盖的单层工业厂房结构体系。
This paper describes the design of a single span one-story factory building, in which the reinforced concrete precast in-situ V-shaped folded plates were used for roofs and walls.
对单层工业厂房中常用的二跨、三跨连续冷弯簿壁槽钢截面墙梁的扭转问题进行了精确的理论分析。
This paper presents precise analysis on wall girder torsion of cold bend thin-section steel channel of 2 or 3 continuous bays commonly used.
对单层工业厂房中常用的二跨、三跨连续冷弯簿壁槽钢截面墙梁的扭转问题进行了精确的理论分析。
This paper presents precise analysis on wall girder torsion of cold bend thin-section steel channel of 2 or 3 continuous bays commonly used.
应用推荐