清洗、削切蔬菜、肉、鱼或家禽等。
削切的形状旨在衬托其功能和朝向。
The shape of the cuts has been designed to compliment the function and its orientation.
这种材料很硬，可以用来削切钢材。（形容词：硬的）
This material is as hard that it can be used for cutting steel.
集料盒外包粉碎室四周设计，可有效防止粉碎时粉碎料漏出最佳剪切角度，阻力小，不容易卡死，提高削切效率；
Aggregate box outsourcing crushing room design, can effectively prevent the leakage of crushing crushing the best shear angle, small resistance, not easy clamping, improves the cutting efficiency;
人们用拱顶石来盖顶，或者把雪块削切得上边缘比下边缘更宽，放进剩下的屋顶缺口里，再用雪来塞满雪块间的缝隙。
They cap the igloo by dropping a keystone, or block with edges cut wider above than below, into the remaining gap in the roof, and "grout" the gaps between blocks of snow with additional snow.
图斯可对一切迟钝的批评不削理睬。
檀香木材，经纵锯或纵削、平切或旋切，不论是否经刨平、砂磨或端接，其厚度超过6公厘者。
Sandalwood , wood sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or end-jointed, of a thickness exceeding 6 mm.
就削失去了一切别的，也问题未来。
山毛榉(山毛榉属)材，经纵锯或纵削、平切或旋切，不论是否经刨平、砂磨或端接，其厚度超过6公厘者。
Beech wood (Fagus SPP.) sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or finger-jointed, of a thickness exceeding 6 mm.
白木材，经纵锯或纵削、平切或旋切，不论是否经刨平、砂磨或端接，其厚度超过6公厘者。
Ramin wood sawn or chipped lengthwise, sliced or peeled, whether or not planed, sanded or end-jointed, of a thickness exceeding 6 mm.
根据对木片切料角的工艺要求可初步确定削片机的基本尺寸。
According to the technological requirement of wood chip cropping Angle, the basic size of chipper could be determined.
用来切、割、斩、削、砍、刺、铡的工具。
Used for cutting, cutting, chopping, cutting, cutting, piercing, hay tools.
作品有两部分组成：一是被切、削下来的橡胶覆盖于墙面，另一部分是弹簧钢条组成的平面几何图形。
The work was made by two parts:One is cut rubber which covers the wall, another part is Geometric plane shapes which were made by Spring Steel bars.
这与传统的干燥疗法以及切（削）痂植皮疗法，有着本质的差别。
This treating process is quite different from dry therapy with escharetomy and skin grafting.
理论分析表明，在超声振动切削中，切液削有一定作用，但不可能在极短的分离时间内浸入刀—屑界面。
Theoretical analyses show that the cutting fluid can difficultly soak into the tool-chip interface within extremely short separating time though there is some action in the UVC process.
为了做出形状各异的面条，师傅们采用了切、削和擀的手法，有时甚至还会用上一根筷子。
They cut, slice, pull and even use a chopstick to create different noodle shapes.
微小型高转速刀柄可实现金属切 削机床的手动和（或）自动换刀；由锥柄和拉钉组成；
The microminiature high rotating speed tool shank can realize the manual or automatic tool changing of the metal-cutting machine, and is composed of a taper shank and a pull nail;
微小型高转速刀柄可实现金属切 削机床的手动和（或）自动换刀；由锥柄和拉钉组成；
The microminiature high rotating speed tool shank can realize the manual or automatic tool changing of the metal-cutting machine, and is composed of a taper shank and a pull nail;
应用推荐