最适合MSR的推荐切削条件是多少？
论述了径向负前角硬质合金滚刀的设计及切削条件。
Design and cutting condition of carbide hob with radial negative front Angle were discussed.
归一化处理使报警门限设定不受切削条件变化的影响。
The normalized processing makes the setting of the threshold for alarm independent from variation of cutting conditions.
选用的材料种类和切削条件不同，可生成不同形态的切屑。
Different kinds of material and machining conditions used will produce chips of different shapes.
分析不同切削条件下层片宽度的变化及其与变形系数之间的关系。
The variation of the lamella width in different cutting conditions and the relation between the lamella width and the chip deformation coefficient are also analysed.
发现在相同切削条件下，该复合材料表面质量优于ZA22合金。
The results show that the surface quality of the composites is better than that of ZA22 alloy under the same parameters.
除了部分程序更正，编辑也可以进行对切削条件下加工周期的优化。
In addition to part program corrections, editing can also be done to optimize the cutting conditions of the machining cycle.
提出可根据数控车床设计时选用的典型切削条件来计算机床总刚度。
This paper proposes that the total rigidity of a machine tool can be calculated in terms of the typical cutting condition at the beginning of design for the CNC lathe.
不同刀具材料与工件材料的匹配在不同切削条件下有不同的临界速度。
There are different critical speeds with different cutting condition and different matching of cutter and work-piece material.
金属的实际分离始于屈服或断裂(视切削条件而定)，从切削刀尖开始。
The actual separation of the metal starts as a yielding or fracture, depending upon the cutting conditions, starting from the cutting tool tip.
探讨晶体材料的切削加工性，重点分析切削条件对实现镜面车削的影响。
The paper presents the machinability of crystal materials, and emphasizes the influence of cutting conditions on the mirror finish.
实验表明，通过切削条件和振动参数的优化组合能够得到满意的纤维尺寸。
It shows that the satisfactory equivalent diameter of fibre can be obtained through the optimization of the above parameters and conditions.
在不同的切削条件下，疲劳裂纹和热裂纹是造成刀具材料失效的主要原因。
The formation of the fatigue cracks and the thermally induced cracks are mainly responsible for the failure of the ceramic tool materials under various cutting conditions.
本文探讨了晶体材料的切削加工性，重点分析了切削条件对表面粗糙度的影响。
The machinability of crystal material is studied, and the influence of the cutting condition on surface roughness is analyzed.
采用灰色关联度分析方法识别不同切削条件下的主要误差源，并进行了实验验证。
The analyzing method of grey relativity is used for identifying main error sources under different cutting conditions, and these results are verified by experiments.
通过理论分析和试验研究，探讨硬质合金刀具在变速切削条件下磨损累积的规律。
With theoretical analysis and experimental research, the regularity of wear cumulation of carbide tools under varying cutting speed conditions is studied.
在高速切削条件下，材料的切削机理将发生变化，切削过程将变得容易，切削热将降低。
In this process the heat of cutting is reduced and the material can be easily cut.
本文根据实验观察，对高速切削条件下连续型带状锯齿形切屑的形成过程进行了分析研究。
Based on the experimental observation, the high speed formation courses of the continuous banding serrated chips are studied and analyzed.
加大插齿刀后角可以有效改善插齿刀的切削条件，提高齿表面加工质量和延长刀具使用寿命。
Enlarging the clearance of gear shaping cutter can improve efficiently its cutting condition, the gear surface quality and tool life.
通过一个典型的生产应用实例，说明了涂层硬质合金车刀切削条件优化的方法和技术经济效盆。
Some essential rules for the application of coated carbide tools are proposed, and a typical example is chosen to show the optimization of the cutting conditions of a coated carbide tool.
实验结果表明，该方法不仅可以在多种切削条件下获得较高的识别率，还可以识别出新的刀具故障。
Experiments indicate that this method has a high ratio of recognition in a range of cutting condition and even can detect novel tool faults.
从理论模型中提出的这项工作，表面形貌可从追溯的切削条件，刀具几何形状，切削工具不完善和铣床偏差。
From the theoretical model proposed in this work, the surface prole can be deduced from cutting conditions, cutter geometry, cutting tool imperfections and milling machine deviations.
第一种是基于电流信号的刀具磨损模型，第二种是直接基于刀具磨损量的模型，这两种模型均滤除了切削条件的影响。
One is the current signal model with bore cutting condition, and the another is the model of tool wear with cutting conditions and time.
经加工试验证明了该表面粗糙度预测模型的有效性，从而实现加工前在确定切削条件下预测和控制表面粗糙度的目的。
It proves that this prediction model is effective by machining experiments. Using prediction model can predict and control surface roughness under certain condition.
试验证明，切削状态当量电阻能有效反映切削条件的变化，通过检测其变化可实现导电加热切削加热电流的最佳控制。
The experimental results show that cutting state resistance is an effective parameter for detecting the change of cutting conditions. As a result, the optimum heating current in elect...
本文首先从切削剪切变形和刀具离散化理论出发，推导出高速铣削条件下铣削力和切削速度的关系模型。
A relation model between cutting forces and cutting speed is established for high speed milling condition on the basis of research into the theory of shear distortion and the discrete milling cutter.
对金属切削有重要影响的条件有工件材料、刀具材料、刀具几何形状、切削速度、进给率、切削深度和所用的切削液。
The conditions which have an important influence on metal cutting are work material, cutting tool material, cutting tool geometry, cutting speed, feed rate, depth of cut and cutting fluid used.
以这两种刀片在不同切削用量条件下的耐用度、加工表面粗糙度和主切削力作为刀具加工性能的评价依据，同时研究了刀片的磨、破损机理和卷、排屑稳定性。
The tool lifespan, surface roughness and main cutting force of the two kinds of tools with different machining parameters are used as the evaluation criterion of machining ability.
以这两种刀片在不同切削用量条件下的耐用度、加工表面粗糙度和主切削力作为刀具加工性能的评价依据，同时研究了刀片的磨、破损机理和卷、排屑稳定性。
The tool lifespan, surface roughness and main cutting force of the two kinds of tools with different machining parameters are used as the evaluation criterion of machining ability.
应用推荐