文章研究的是在成组要素的位置度测量中，如何获取其最优结果的一种计算方法。
What this text was studied is in the measurement of grouped key elements position degree, how to procure the most excellent result of computational method.
应采用剖面测量法在每个工作生产换班时间也就是每12小时从3个不同的位置进行测量，以确保准确的表面粗糙度。
Profile measurements, to ensure the correct anchor pattern, shall be taken at a minimum of three (3) different locations for each working production shift, i. e. twelve (12) hours.
轮廓的尺寸量、位置量以及形状误差估计值的不确定度与测量误差、被测轮廓的形状特征以及采样策略等有关。
Sampling strategy, measurement errors and measured contour form features are all related to the uncertainty analysis for dimension, position and form error estimated.
它不仅可以测量内径、外径和直线度误差，还可以测量孔中心距、锥度和同轴度、垂直度等位置误差。
It can measure not only the inner diameter, outer diameter and linearity error, but also the center distance between holes, taper and position errors such as coaxality, verticality, etc.
实验表明，该校准方法适合于多关节坐标测量机结构参数真值的获得，并可极大地提高测量机的位置准确度。
It is demonstrated by experiment that this calibration is suitable for obtaining true structure parameters of links and the position accuracy of multi joint CMM can be improved greatly.
它不仅能测量尺寸、形状误差，还可以测量垂直度、锥度、孔中心距、平行度等相互位置误差。
It can be used in measuring not only dimensional and shape errors, but also relative positions as in the cases of perpendicularity, parallelness, conicity, distance between holes, etc.
MT850型车轮动平衡机能自动测量车轮的不平衡度，并且自动将车轮停在要平衡的位置。
MT850 automatic measurement function type wheel balancing wheel imbalance, and automatically stop the wheels to balance position.
MT825型车轮动平衡机能自动测量车轮的不平衡度，并且自动将车轮停在要平衡的位置。
MT825 automatic measurement function type wheel balancing wheel imbalance, and automatically stop the wheels to balance position.
通过移站测量来获得几个固定点的坐标位置，然后将测量结果进行处理，给出整个测量系统的测量不确定度。
By measuring the coordinate positions of a series of fixed targets from several instrument locations and calculating the measurement results, the working uncertainty of the total system will be given.
提出一种眼镜度数测量方法，利用位置探测器和3条光线实现对棱镜度、球镜度和散光度等镜片参数的测量。
A position detector and 3 beams of ray are used to measure the prismatic, spherical and astigmatic powers.
在直线度测量数据处理过程中，运用坐标变换法时，往往不能一次正确估计“高—低—高”或“低—高—低”点的位置，所以需通过多次坐标变换才能达到目的。
As the data of straightness measurement are processed, Coordinate Transform method can not estimate the positions of High-Low-High or Low-High-Low correctly once.
一种测量机械零件位置误差的轴键槽对称度检测仪。
The utility model relates to a symmetrical characteristic detector for the axial key groove which can measure the positional error of the machine parts.
干涉条纹幅度最大点处确定为绝对零角度位置，因此该方法可以实现角度的绝对测量。
The absolute zero angle can be defined at the biggest fringe amplitude point, so this method can also achieve absolute angle measurement.
机械设备检测是对机械零件中包括长度、角度、粗糙度、几何形状和相互位置等尺寸的测量。
Machinery and equipment testing includes the measurements of length, Angle, roughness, geometry and mutual alignment.
将仪表安装到测量位置上，接通电源，通过表壳体上标牌下的调零、调满螺钉对零点和满度进行调整。
After installation and supplying power, you can adjust the Zero and full scale according the label on the housing.
将仪表安装到测量位置上，接通电源，通过表壳体上标牌下的调零、调满螺钉对零点和满度进行调整。
After installation and supplying power, you can adjust the Zero and full scale according the label on the housing.
应用推荐