根据油井管螺纹不同部位产生毛刺的特点，讨论了去除和控制毛刺的相应工艺方法。
Based on the features of burrs generated on different areas of the thread, the corresponding deburring technologies are discussed.
当传统的毛刺和材料整理方法不能产生必要的成果，产业化的挤压珩磨。
When conventional deburring and material finishing methods fail to produce the required results, industry turns to Extrude Hone.
去毛刺-钻孔后会在铜箔和孔壁上产生粗糙边。
Deburring As drill removes copper a small copper ridge forms around the hole edge.
并提出了被切削层金属沿刀具切削刃向工件两侧的自由表面产生塑性流动是形成两侧方向毛刺主要原因的新观点，得到了试验结果的证实。
A new viewpoint was advanced, in which the plastic flow of metal layer to be cut becomes the cutting burr, and it was confirmed by experimental results.
毛刺是金属切削加工中产生的常见现象。
The burr is one of the common phenomena occurring in metal cutting.
特点：FPC加工专用钻头，切削锋利，能有效抑制毛刺和钻污的产生。
Features: With sharp cutting teeth for preventing burr and smear generation. Suitable for machining FPC and PTFE.
在这种情况下，睫毛刺激眼睛产生眼泪。
In these conditions, the lashes irritate the eye, causing the tears.
油井管螺纹切削加工中产生的毛刺会直接影响螺纹检验的准确性和螺纹连接质量。
The accuracy of thread inspection and quality of threaded connection will be influenced by burrs resulted from the thread cutting process of tubing and casing.
湍流-切割管道时留下的毛刺使流体产生旋转作用，导致局部侵蚀，从而最终造成故障。
Turbulence - burrs left on the cut tubing causes a tumbling effect causing localized erosion and eventual failure.
为避免重复过切以及由此产生的毛刺必须使用以下三种之一的过切设计。
Carrier design must be developed in one of three ways to avoid match cuts and the burrs that are associated with them (no burrs are exceptable in these area's).
第三、切面特别光滑，没有毛刺的产生，切口是很精细的，对工件没有任何伤害，因为它是不接触材质的，不会划伤切割的物体。
Third, the plane is particularly smooth, no burr, the incision is very fine, no damage to the workpiece, because it is not contact material, will not scratch the cutting object.
由此产生的化学毛刺将放在快车道心脏病，中风，糖尿病和肥胖，甚至你。
The resulting chemical glitches will put you on the fast track for heart disease, stroke, diabetes and even obesity.
对于差分输出的数模转换器，设计了能够产生高交叉点控制信号的电流源开关控制电路以减少输出的毛刺提高整体的动态性能。
For the difference output, designs a current switch signal generator with high cross-point and restricted voltage range to decrease the glitch of output, in order to obtain a good dynamic performance.
金属切削加工过程中，在已加工零件的表面上存在鳞片状的毛刺，本文通过对鳞刺成因进行探讨，分析其产生的过程和原因，找出控制鳞刺的方法和措施。
In the process of metal machining, flake's burr occurs on the surface of the processed part. With analysis of causes of flake's burr, this paper explores countermeasures to control the flake's burr.
工件表面洁净度影响小，利用电流缓升，缓降焊功能可以减少焊接时产生的火花飞溅和毛刺。
The influence on the surface smoothness of parts is small and the slow increase and decrease of welding function reduces the spark flashing and burs during welding.
工件表面洁净度影响小，利用电流缓升，缓降焊功能可以减少焊接时产生的火花飞溅和毛刺。
The influence on the surface smoothness of parts is small the slow increase decrease of welding function reduces the spark flashing burs during welding.
工件表面洁净度影响小，利用电流缓升，缓降焊功能可以减少焊接时产生的火花飞溅和毛刺。
The influence on the surface smoothness of parts is small the slow increase decrease of welding function reduces the spark flashing burs during welding.
应用推荐