主要探讨不同烧结温度对产品各项性能指标的影响。
The influences of different sintering temperatures on the properties were discussed.
本文以拜耳法新赤泥和黄河河砂为原料，按不同配比和不同烧结温度进行烧结。
In this paper, Bayer new red mud and the Yellow river sand as raw material, firing sintered brick According to different ratio and sintering temperature.
应用 X-射线衍射和扫描电子显微镜研究不同烧结温度下材料的相组成和显微结构特征。
X ray diffraction and scanning electron microscope were used to investigate the phases and microstructure of products sintered at different temperatures.
结果表明， 在不同烧结温度下，烧结体中各元素之间产生冶金结合， 且合金化程度随温度的升高而增大。
The results show that the bonding way between elements is metallurgical bonding and the alloying rate rises with the increase of sintering temperature.
采用液相烧结法将爆炸压实后的WC钢结硬质合金粉末复合在碳钢表面，对不同烧结温度下的界面组织和抗剪强度进行了研究。
WC steel-bonded cemented carbide powders being compacted by explosive compaction were bonded to the surface of carbon steel using liquid phase sintering.
并对不同烧结温度下纳米氧化锆进行了测量，结果表明纳米氧化锆的杨氏模量随烧结温度的升高而增加，此方法简便实用，并对试样的形状无特殊要求。
Result shows the Youngs modulus of nanometer ZrO 2 increases with elevated sintering temperature. This method is simple and practicable, and has not special demand for shape of sample.
根据材料和烧结温度的不同，零件的密度在烧结过程中也会改变。
The density of the component can also change during sintering, depending on the materials and the sintering temperature.
重点论述了涂层在发动机不同零件上的浆料成份及粘度、涂覆方法、烧结温度和工艺过程。
The coating of the slurry composition, viscosity, coating means, sintering temperature and coated technological process which is applied to different parts are studied.
主要探讨了不同的烧结温度对试样的耐压强度和体积密度的影响。
The effects of different temperatures on compressive strength and bulk density were studied.
随着烧结条件的不同，介电常数几乎不变，但介电损耗以及介电常数的温度系数则较为敏感。
The dielectric constant was almost a constant, while the dielectric loss and temperature coefficient of dielectric constant were sensitive to the sintering conditions.
实验结果表明，硅片中的应力分布随烧结温度的不同而不同，应力随烧结温度的降低而减小。
Experimental results indicate that the stress distribution varies with the sintering temperature, and that the stress decreases with the sintering temperature.
并给出了在不同的成形压力和不同的烧结温度下的实验结果。
Experimental results at different shape pressures and sintering temperatures are given.
在陶瓷生产领域，陶瓷产品由于各自的工艺性能不同，对其烧结温度都有严格的要求。
In the ceramic industry, since the processing performance of each product is different, ceramic has the strict requirement to sintering temperature.
为了解铜氧化物高温超导体的正常态输运特性对其超导电性的影响，我们对不同温度烧结样品正常态电阻率和超导电性之关联进行了系统的研究。
In order to know the influence of the superconductivity by normal properties of the cuprate superconductor, the relationship between the normal resistivity and the superconductivity was studied.
根据DIL分析确定不同物质掺杂钛酸锶的最佳烧结温度，采用排水法测定了试样的烧结密度；
The optimal sintering temperature of SrTiO3 doped with different substances was investigated based on DIL analysis. Density of samples was measured by the Archimedes principle.
根据DIL分析确定不同物质掺杂钛酸锶的最佳烧结温度，采用排水法测定了试样的烧结密度；
The optimal sintering temperature of SrTiO3 doped with different substances was investigated based on DIL analysis. Density of samples was measured by the Archimedes principle.
应用推荐