go top

网络释义专业释义

  microstructure and mechanical property

...t treatment ; GCr15 ; microstructure and mechanical property [gap=317]关键词:粉末冶金 真空热处理 GCr15 组织与性能 ...

基于28个网页-相关网页

  Organization And Performance

...ture And Properties ; Structure And Performance 组织与性能 microstructure and properties ; Organization And Performance ; Microstructure And Performance ; Structure And Performance 钢的组织与性能 Steel Microstructure and Properties ..

基于8个网页-相关网页

短语

组织与性能的变化 Evolution of Microstructures and Properties

显微组织与性能 Microstructure And Performance

强化层的组织与性能 Microstructure and properties of hardened surface

  • microstructure and properties - 引用次数:40

    The result showed that there were remarkable changes in the microstructure and properties after adding these elements.

    结果表明,这些元素的加入明显改变了合金的组织与性能

    参考来源 - 新型镁铝锌合金组织与性能的研究
    microstructures and properties - 引用次数:12

    In this paper, microstructures and properties of low-carbon and low-alloy weld are mainly numerically simulated.

    本文就是主要针对低碳钢和低合金钢的焊缝组织与性能进行数值模拟。

    参考来源 - C
    microstructure and property - 引用次数:10

    The heat treatment process hasbeen optimized for QAl10-4-4 valve cross test. The changing law of microstructure and property under different heattreatment processes and the effects of actual heat treatment conditions on property have been investigated and discussed.

    分析了QAl10-4-4制铜阀性能波动的原因,采用正交试验优选了QAl10-4-4材料的热处理工艺,研究和讨论了其不同热处理条件下组织与性能的变化规律及实际热处理条件对铜阀性能的影响。

    参考来源 - QAl10
    microstructures and mechanical properties - 引用次数:5

    However, the sorts of high-strength titanium alloysare few at home and the study on microstructures and mechanical properties ofhigh-strength cast titanium alloys is not systematic, too.

    目前我国高强度钛合金材料的种类较少,对铸造高强度钛合金的组织与性能研究也不系统。

    参考来源 - BT22高强度铸造钛合金组织与性能的研究
  • microstructure and performance - 引用次数:3

    The influence of different processing parameters (including: calcination temperature, reduction temperature, pressing, sintering temperature, sintering time and repressing) on the microstructure and performance of composite powders and ND/Cu composite bulks were investigated, and then processing parameters were optimized.

    研究了不同制备工艺参数(包括:煅烧温度、还原温度、初压压力、烧结温度、烧结时间、复压压力)对复合粉末、复合材料微观组织与性能的影响,确定了最佳的制备工艺参数。

    参考来源 - 化学共沉积法制备纳米金刚石/铜基复合材料的研究
    microstructure and property - 引用次数:2

    参考来源 - 预氧化法制备Cr
  • microstructure and properties - 引用次数:1

    参考来源 - 高速铁路用低碳贝氏体鱼尾板性能研究

·2,447,543篇论文数据,部分数据来源于NoteExpress

双语例句

  • 结果表明以锰低碳高合金钢可以获得预期组织性能

    The results indicate that LCHA with Mn in place of Ni could gain the anticipated structure and performance.

    youdao

  • 同时研究极化处理LTA陶瓷复合材料组织性能影响

    Also, the effect of polarization treatment on microstructure and mechanical properties of LTA ceramic composite was studied.

    youdao

  • 通过组织性能综合评价得出了激光熔铸涂层的最佳工艺参数

    The best technological parameters of laser surface melt casting were obtained through comprehensive analysis of structure and properties.

    youdao

更多双语例句
$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定