...路(open circuit)四种,并指出放电过程中有效放电的 放电时间(discharge duration)可用來测量材料移除率 (material removal rate);根据放电时间的总和求出最佳 平均放电电压,以平均放电压为參數來控制加工过 程;并提出有效放电的放电时间分布与加工參數的关...
基于12个网页-相关网页
此类数控加工技术与装备的特点及要求可概括为: (1)采用高速主轴系统,提供尽可能高的材料去除速率(Material Removal Rate,MRR),当前应用的高速主轴,转速可达42000r/min,甚至更高。
基于8个网页-相关网页
...后,我们接下来便依照图七所示的三种实验状态进行 CMP 实验,至于我们主要观察的指标分别为材料移除率(Material Removal Rate,MRR)及不 均匀度(Within Wafer Non Uniformity,WIWNU)指标。
基于8个网页-相关网页
此类数控加工技术与装备的特点及要求可概括为: (1)采用高速主轴系统,提供尽可能高的材料去除速率(Material Removal Rate,MRR),当前应用的高速主轴,转速可达42000r/min,甚至更高。
基于6个网页-相关网页
Low Material Removal Rate 磨削去除率小
maximum material removal rate [机] 最大去除率
the material removal rate 材料去除率
specific material removal rate 比材料去除率
zeitspanungsvolumen material removal rate 材料切削量
removal rate of material 材料去除率
Only depth of cut and federate have effects on material removal rate (MRR).
仅当切削深度、进给速度等参数值增加时,材料去除率增加;各参数变化独立对材料去除率产生影响,参数之间没有相互的影响关系。 (3)对切削压力影响最大的加工参数是磨料粒度。
参考来源 - 旋转超声波铣削加工技术的实验研究When grinding feed rate increases, the material removal rate increase.
当磨削进给速度增加时,材料切除率增加。
参考来源 - 核电高压容器壳体焊缝高速强力砂轮磨削技术研究Greater material removal rate can be obtained when machining gap is 60μm & 90μm, machining time is 20min and rotational speed is 2000rpm & 2700rpm.
当外部加工参数选用加工间隙60μm、90μm,加工时间20min,工具转速2000rpm、2700rpm时材料去除率较高。
参考来源 - 磁流变效应微砂轮超精密研抛加工机理研究·2,447,543篇论文数据,部分数据来源于NoteExpress
These measurements have correlated well with those made in conventional constant material removal rate grinding tests.
这些测量结果与用传统的恒磨除率磨削试验具有良好的相关性。
The existence of the soft layer could increase the material volume removed by one particle and increase the material removal rate during CMP.
软质层的存在一方面增大单个磨料所去除材料的体积,增加材料去除速率;
Adding the right amount of the additives and increasing the particle size can improve the effect of the mechanical reaction to achieve higher material removal rate.
加入适量添加剂,可增大反应产物的体积,易于提高机械作用的效果,以获得较高的去除速率。
应用推荐