当前查询结果是否对您有帮助
go top

bending strength

  • [力] 弯曲强度;[力] 抗弯强度

网络释义专业释义

  [力] 弯曲强度

[ 模拟技术] 主题:电子类术语3 ... bench mark,水准点 bending strength,弯曲强度 bending vibration,弯曲振动 ...

基于1126个网页-相关网页

  抗屈强度

万能工具铣床维修机械维修电器等专用工具术语汉英对照 ... 均角投影图;等角投影图 isometric drawing 抗屈强度 bending strength; yield strength 介电常数;电容率 permittivity ...

基于312个网页-相关网页

  抗折强度

推荐上海江苏宁波绿色耐磨地坪材料生产厂家 ... 抗压强度pressurestrength 抗折强度Bending strength 抗拉强度Tensile strength ...

基于134个网页-相关网页

短语

repeated bending stress strength 反复弯曲疲劳强度极限

bending ultimate strength 抗弯强度

bending tensile strength 抗弯拉强度

bending yield strength 弯屈服强度

vertical bending ultimate strength 船体垂向弯曲最终强度

bending endurance strength 弯曲疲劳强度

tooth bending fatigue strength 弯曲疲劳强度

teeth bending fatigue strength 轮齿弯曲疲劳强度

bending fatigue strength 弯曲疲劳强度

 更多收起网络短语
  • 弯曲强度 - 引用次数:89

    At high temperature, bending strength of TiC-Ni cermets decreased with temperature increasing and plastic distortion took place beyond 1000℃.

    随着温度的升高,TiC-Ni材料弯曲强度下降,温度超过1000℃开始发生塑性变形。

    参考来源 - 燃烧合成TiC
    抗弯强度 - 引用次数:73

    Correspondingly, the wrapping materials have smaller effects on the tensile strength, and the species of the rattan cane have smaller effect on the bending strength.

    缠结材料对抗拉强度影响显著程度相对较小,基材对抗弯强度影响显著程度相对较小。

    参考来源 - 藤家具质量评定及检验方法的研究
    齿根应力 - 引用次数:4

    On the condition of knowing the root stress value of x-zero gear, the bending strength of x-gears with the same teeth can be calculated through the formula.

    在已知标准齿轮齿根应力值的前提下,通过该计算式便可算出任一变位下的齿根最大应力

    参考来源 - 渐开线变位齿轮参数化精确造型与齿根应力分析的研究
  • 抗弯强度 - 引用次数:54

    The bulk density of this material is 2.71 g/cm3, the bending strength is 120MPa, the dielectric constant and the dielectric loss at 1MHz are 8.6 and 1.27×10-3 respectivly.

    烧结试样的体积密度为2.71g/cm3,抗弯强度为120MPa;在1MHz的测试频率下,其介电常数为8.6,介电损耗为1.27×10-3。

    参考来源 - CBS/Al
    弯曲强度 - 引用次数:39

    Adding of LDPE causes the melt strength to grow but the stretching and bending strength to decrease.

    低密度聚乙烯用量增加时,熔体强度会有所上升,但力学性能会下降。 总的说来,熔体强度高的产物冲击强度较高,但拉伸强度弯曲强度有下降的倾向。

    参考来源 - 高熔体强度聚丙烯的研究
    抗折强度 - 引用次数:20

    At the same condition,the bending strength and bulk density of sample made of retotite were better than that of sample of kaolinite.

    ③在相同条件下,以累托石质配方制备的样品的抗折强度、体积密度大于以高岭土质配方制备的样品。

    参考来源 - 用累托石制备多孔陶瓷的研究
  • 抗折强度 - 引用次数:2

    Comparison of the compressive and bending strength of set cement for different formulations and curing time, the use of early-strength agent ranging from 1.2% to1.8% can significantly improve the early-strength of set cement.

    通过对不同配方和不同养护时间的水泥石压、抗折强度实验对比得到:加入早强剂可以显著提高配方水泥石的早期强度,早强剂加量范围为1.2~1.8%之间。

    参考来源 - 漂珠+微硅低密度水泥浆配方的实验研究
  • 挠曲强度
    抗折强度
    抗挠强度
    抗屈强度
  • 抗弯曲强度
  • 抗弯强度
    弯曲强度

·2,447,543篇论文数据,部分数据来源于NoteExpress

同近义词

双语例句权威例句

  • Bending Strength and Weibull modulus of eight kinds of ceramics samples were studied.

    研究了不同陶瓷试样抗弯强度韦布尔模数

    dict.cnki.net

  • The result shows that the bending strength and hardness of the composite is remarkably increased but the effect on the resistivity of the composite is not obvious.

    结果表明镀铜石墨-复合材料中加入镀铜碳纤维可以明显地提高抗弯强度硬度材料电阻率作用并不明显

    dict.cnki.net

  • Conclusion:The values of fatigue strength and bending strength of the bone cement were improved by vacuum mixing. The method of vacuum mixing has an active significance in clinic.

    结论采用真空搅拌水泥方法提高国产水泥抗疲劳强度静态抗弯曲强度临床应用较大的积极意义

    dict.cnki.net

更多双语例句
$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定