挤压成型法(extrusion moulding)是指强力挤压可塑性泥料使其通过孔模成型的方法。挤压成型与可塑成型都是采用可塑性泥料,两者的区别在于挤压成型需用强力挤压的挤压机,动力的来源为液压、压缩空气或机械加压,多用于特殊耐火材料的生产。特殊耐火材料用的原料大多属于瘠性料,不具有可塑性。在挤压成型前必须将其塑化,通常加入塑化剂或粘结剂使其成为可塑料。工业生产中常用糊精、工业糖浆、羧甲基纤维素、聚醋酸乙烯脂、聚乙烯醉等有机塑化剂。
文章详细信息 关键词: 挤压成型;纤维增强水泥板;尺寸稳定性;收缩 [gap=850]Keywords: extrusion molding;fiber reinforced cement board;dimensional stability;shrinkage
基于46个网页-相关网页
(1)挤压成型(Extruding) 挤压成型一般是将真空练制的泥料,放入挤制机内,这种挤制机一头 可以对泥料施加压力,另一头装有机嘴即成型模具,通过更换机嘴...
基于20个网页-相关网页
1定义 定义 挤压成型( 挤压成型(Press Forming)是对放在模具模腔 ) 或挤压筒)内的的金属坯料施加强大的压力, (或挤压筒)内的的金属坯料施加强大的压力, 使金属坯料产生定...
基于12个网页-相关网页
在磨具内挤压成型 Forming
挤压成型工艺 CMT
挤压成型机 extrusion moulding machine ; squeeze forming machine ; single-lead-screw extruding briquetting machine
糊膏挤压成型法 paste process
挤压成型绝缘管 Extruded insulating tubing
挤压成型催化剂 extruded catalyst
挤压成型焊条 extruded electrode
挤压成型法 Extrusion Forming ; extrusion moulding
螺旋挤压成型 screw extruding briquetting
In this dissertation a lot of methods about making porous ceramics, including sol-gel process, polymeric sponge impregnation process, addition pore-forming material process, extrusion process were introduced.
本文介绍了多孔陶瓷的传统制备工艺如溶胶-凝胶工艺、有机泡沫浸渍工艺、添加造孔剂工艺、挤压成型工艺等。
参考来源 - 多孔陶瓷的制备及特性研究·2,447,543篇论文数据,部分数据来源于NoteExpress
提出了虎克式万向节热挤压成型的可行性。
The feasibility of the joint hot extrusion forming was put forth.
采用糊态挤压成型镁合金避免了压力铸造的缺点。
By using mushy extrusion molding for magnesium alloy, the disadvantage of pressure casting is avoided.
在烧结过程中,陶瓷粉末先挤压成型然后加热到略低于熔点温度。
In sintering, ceramic powders are processed into compacted shapes and then heated to temperatures just below the melting point.
应用推荐