本文也指出了由于应变率敏感性所引起的内耗增量和过应力的类比性。
The analogy between internal friction increment and overstress due to strain-rate sensitivity is clarified.
经典塑性本构关系、多屈服面本构关系及过应力型粘塑性本构关系只是本文的特例。
The classic plastic constitutive relation, multi-yield surface constitutive relation and over-stress viscoplastic constitutive relation are a special example of this constitutive relation.
将材料响应的总应力表示为平衡态应力和非平衡态过应力的和,分别定义描述率无关和率相关变形过程的内时。
The total stress response of material is decomposed into a sum of an equilibrium stress response and a non-equilibrium overstress response.
对预应力管道,预应力通过套管与裂纹管道过盈配合方式产生。
To prestressed sleeve, prestressed produced through interference fit between sleeve and crack pipeline.
并对车轮车轴应力分布,飞轮离心力对紧固力过盈量的影响作了论述。
The stress distribution on wheel shaft and the effects of flywheel centrifugal force on its tight fit are discussed as well.
用合适的率定过的量测计控制预应力钢索的拉力。
Suitable calibrated dynamometers were used to control the pull in the prestressing cables.
我们已能够通过比较经历过常规应力解除芯片来确认被改进芯片强度的平均、最小、最大值。
We have been able to confirm that average, minimum and maximum values for die strength could be improved compared with die that underwent the conventional stress relief.
上的应力的作用,逐滴运动诱导的壁附近的对称轴的区域中,从而增加了当初始放置过的距离的增加被限制。
The action of the stress on the wall induced by drop motion is restricted in an area near the symmetric axis, which increases when the initial stand-off distance increases.
由于过盈配合组合厚壁筒内会产生装配应力。
The assembling stress appears in combined thick wall cylinder because of assemblage excess.
和多厚环过盈套装的方法结合起来装配飞轮,可以有效地增大径向压应力,缓和环向应力;
The method of combination of the two ways can availably increase the radial compressive stress and smooth the hoop stress.
我曾在我的工作中说过,如果想要长久地保持你的适应力,那么就必须让自己复杂化。
In my own work, I have argued that, if you want to preserve your ability to adapt to change, you need to "complicate yourself".
急性创伤性损伤中以踝关节扭伤多见,过劳性损伤以应力性骨折为主。
Ankle sprain was most frequently seen in acute traumatic injuries while stress fracture was the most frequent in exhaustive injuries.
对于过洪时未到设计龄期的混凝土,考虑温度载荷的应力值大于不考虑温度载荷的应力值。
To the RCC concrete that under design RCC concrete age when flowing design flood, the stress value considered the temperature load is bigger than that does not consider the temperature load.
计算链板和套筒的过盈应力的方法有:二次计算法和附加刚度法;
The calculation of the interference of the cover and sleeve is as follows:secondary calculation and additional rigidity method.
由于这是一种非破坏试验方法,所以仅一个模型就可以对几种不同转速以及静过盈状态下的应力进行测定。
The test method employed is non-destructive, so that only one model is needed for investigating stresses in a rotating disc at various speeds, and for determining the static shrink fit stresses.
本文用权函数法导出了由套装应力引起的组合厚壁筒内边裂纹的应力强度因子公式 ,这些公式可用于计算组合厚壁筒在不同裂纹深度、材料、过盈量和尺寸情况下的应力强度因子。
The weight function formulas are worked out and can be used for all kinds of depth of crack, materials, assemblage excess, size of combined thick wall cylinder to compute the stress intensity factors.
锥面过盈;位移;应力;有限元方法;尺寸影响系数;
Tapered interference; Displacement; Stress; Finite element method; Dimension effect coefficient;
边坡开挖后,原有应力平衡遭破坏,若边坡过高、过陡,将产生失稳。
After the digging of a slope, its original stress equilibrium was broken. The slope would lose stability if the slope was high and steep enough.
边坡开挖后,原有应力平衡遭破坏,若边坡过高、过陡,将产生失稳。
After the digging of a slope, its original stress equilibrium was broken. The slope would lose stability if the slope was high and steep enough.
应用推荐