两轴运行的排调心方对球轴承齿轮，和一个标准就在轴箱弹簧的另一端密封球的比赛，两个12毫米口径。
The axles run in two-row self aligning ball bearings on the gear side, and a standard sealed ball race on the other end in the sprung axle box, both 12mm bore.
释放轴心和左侧的轴端盖子。之后取出轴承。
研究了非线性弹性转子-轴承系统的轴心轨迹，认为对称不平衡转子是连续弹性轴，它两端支撑在滑动轴承上，油膜反力采用非线性短轴承模型。
With reference to a symmetrical unbalanced rotor treated as a continuous elastic shaft suPPorted at its end by lubricated journal bearings, the short bearing model is adoPted.
在内端盖与机座的连接 处法兰上铣一个与轴承盖上所铣平面位置相对的槽，槽内放置测速传感器；将 轴头压板改为齿盘结构。
A groove is milled on the flange for installing the speed sensor at the junction of the inner end cap and the seat, which is facing to the plane on the bearing cap.
由世纪两端轴承上的平衡轴有可能产生的钻石。
By the ends of century the upper bearing of the balance shaft were likely to have the diamonds.
主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
它包括转动轴、安装在转动轴两端的轴承、安装着轴承的两个轴承座。
The rotating shaft mechanism comprises a rotating shaft, bearings installed at the both ends of the rotating shaft and two bearing seats installed with bearings.
留有开口的半环形轴承，用于内啮合齿轮双端支承及定轴齿轮箱。
A semi-annular bearing with an opening is used to support both ends of inside engaged gear or for fixed-axle gear box.
多个轴承位于该扭力杆第一端与该平衡轴中心孔之间，将该扭力杆置于该平衡轴的中心。
Bearings are located between the first end of the torsion bar and the center bore of the balance shaft, to center the torsion bar within the balance shaft.
该型适用于非常温环境下，主机两端轴(轴承)安装无法严格同心时的径向负荷上使用。
This type is suitable for high temperature environment, the host end shafts (bearing) installation could not be strictly concentric when the radial load on the use of.
在内圈的一端，轴承通过偏心锁定环(图1.7)或者两个定位螺钉(图1.8)被固定在轴上。
At one end of the inner ring, the bearing is clamped to the shaft with an eccentric locking ring (Figure 1.7) or with two setscrews (Figure 1.8).
宝盟夜蛾的组合是由两端和至少一个传感器系统，轴承安装的共同特点是轴的轴承之间。
The Baumer Hübner combinations are characterized by a common shaft with bearings at both ends and at least one sensor system mounted between the bearings.
同样装好同一根轴上的另一端轴承和座，将轴转动几圈，让轴承本身自动找正位置后。
Also installed on the same shaft to the other side of the bearing and seat, will turn a few laps, let shaft bearing itself automatically find the position is.
在芯轴端部 内侧设置滚针轴承，使整个轮毂单元的受力平衡，运转更平稳。
The internal of the core axle end is provided with a needle bearing, which balances the bearing of assembly wheel hub and enable the operating more stable.
换向器端轴头装有测速齿盘，换向器轴承盖留有轴承温度传感器安装口。
Frame is a press-formed welded fabrication and hugging bearing or bush structure; Speed gear plate is mounted on shaft end of commutator.
该电动机包含机座、机座换向 器端的与机座固定的内端盖、与内端盖固定的轴承盖和位于轴承盖和轴承之间 的轴头压板；
The motor contains a seat, an inner end cap on the commutator connecting to the seat, a bearing cap connected with the inner end cap, an end plate between the bearing cap and the bearing.
它的两端安装在球面轴承上，因而对于两端轴承座与转动轴中心线的同心度要求不高；
The both ends are installed on the spherical bearings, therefore, the requirement of concentricity of the bearing seats at the both ends and the central line of the rotating shaft is not high;
另外，由转频附近细化谱分析及时域波形比较，发现输入轴非电机端轴承座内机件还有径向配合松动故障。
Besides, at the non-drive-end of the primary shaft, some mechanical fitting in the bearing case were detected loosen, through spectrum-zoom analysis and waveform comparison in the time-domain.
另外，由转频附近细化谱分析及时域波形比较，发现输入轴非电机端轴承座内机件还有径向配合松动故障。
Besides, at the non-drive-end of the primary shaft, some mechanical fitting in the bearing case were detected loosen, through spectrum-zoom analysis and waveform comparison in the time-domain.
应用推荐