筒体与轴两端的相连处装有四重轴端密封装置。
Two ends of the mixing axis that articulates with the mixing silo are loaded quadruple axle end seal device.
kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
针对离心通风机传动组的轴端密封经常漏油这一现象，提出了改进措施。
Improving measures are put forword against the phenomenon of shaft end seal of oil leakage of centrifugal fan driving unit.
介绍了150SBD-12型离心式砂石泵轴端密封的结构原理和相应的技术措施。
The principle and technique of sealing of shaft end of the 1150SBD-12 centrifugal gravel pump are introduced.
本系列齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成，齿轮油泵巩义市电话： 。
This series of gear pumps are gear, shaft, pump, safety valve, shaft seal formed.
该搅拌机主要由搅拌筒体、搅拌轴及其轴端密封装置，以及主传动机构和卸料机构等部分组成。
Tthe mixer is primarily composed of mixing silo, mixing axis and their axle end seal device, main drive gear and discharging mechanism etc.
主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
泵轴端密封设计为两种形式，一种为机械密封，一种是填料密封，可根据具体使用情况和用户要求确定。
Pump shaft seal is designed to end in two forms, one for the mechanical seal, one is packing seal, may be based on specific usage and user requirements to determine.
由于其介质为高炉煤气，属于易燃、易爆、有毒气体，所以要求透平膨胀机的轴端密封系统必须安全可靠，且运行经济。
Its medium is blast furnace gas which is inflammable, explosive and toxicant. Therefore, the shaft end sealing system of a turbine expander must be safe and reliable, and has economic running.
以新型泥状填料为研究对象，通过对密封原理的分析及新老泵类轴端密封材料性能的比较，从而得出两代密封材料的优缺点。
A new muddy packing is investigated by analyzing principle of packing seal and comparing with other shaft seal materials in pumps.
两轴运行的排调心方对球轴承齿轮，和一个标准就在轴箱弹簧的另一端密封球的比赛，两个12毫米口径。
The axles run in two-row self aligning ball bearings on the gear side, and a standard sealed ball race on the other end in the sprung axle box, both 12mm bore.
其密封件固有的安装裙被压紧在端盖上，可防止密封件随着轴的转动而转动。
It will be tightly fixed on the end cover which can prevent seals from rotating while shaft rotating.
过大的轴会增加唇端的接触载荷，而过小的轴则会使唇端接触面上的密封压力不够。
Too much lip-axis will increase the load-side contacts, while the shaft is too small it will end lip of the seal contact surface pressure enough.
过大的轴会增加唇端的接触载荷，而过小的轴则会使唇端接触面上的密封压力不够。
Too much lip-axis will increase the load-side contacts, while the shaft is too small it will end lip of the seal contact surface pressure enough.
应用推荐