螺杆压缩机的转子齿面间实际上留有间隙，因而能耐液体冲击，可压送含液气体、含粉尘、易聚合气体等。
Screw compressor rotor tooth surface actually gaps between, and ability, can be pressed send impact liquid containing liquid gas, including dust, easy polymerization gas, etc.
采用高分辨率的增量式光电编码器和相应的硬件接口电路，实现了变磁阻电机转子在定子两个齿之间位移的检测。
Using an optical incremental encoder and hardware interface, the position of the motor rotor between the two teeth of the motor stator is measured.
摆线齿形的内啮合齿轮泵又叫做摆线转子泵，泵中的小齿轮和内齿轮只相关一个齿，因此这种内啮合齿轮泵不需要设置隔板。
Cycloidal tooth profile of the internal gear pump, also called cycloidal rotor pump, pump the small gear and internal gear only related a tooth, so the internal gear pump do not need to set partition.
提出一种在转子上设置虚拟支承的方法，以保证弧齿锥齿轮的啮合稳定性，并采用传递矩阵法，建立了弧齿锥齿轮-转子系统的振动模型。
This paper presents a method of providing a virtual support for the rotor to assure the meshing stability of a pair of a pre determined spiral bevel gears in rotation.
论述了转子叉形齿叶根销孔加工用钻模的设计方法及制造时关键要点。
This paper gives the design method and key point during machining of pin holes on rotor for the fork-type blade root.
介绍了定子齿面加辅助凹槽和转子磁极分段移位两种抑制磁阻转矩的方法。
Two methods of reducing cogging torque, namely, the stator tooth notching and the two rotor pole stacks shifting are presented.
对对称螺杆风机转子的齿型、结构参数等方面的设计理论和方法进行了探讨和研究。
In this paper, the design theory and method of rotor tooth model line for fans with symmetrical screw, its design parameter and so on are discussed and studied.
分析结果表明：热变形是单齿转子压缩机转子变形的主要因素，转子的铸造空腔结构导致转子径向变形很不均匀。
It is shown that thermal deformation is the dominant influencing factor, and that the casting cavity of the rotor results in the serve non-uniform of redial deformation.
直接驱动数控转台；不等齿顶宽；双转子；移相技术；重复控制。
Direct Drive NC Table; Unequal Teeth Tips Width; Dual-Rotor; Phase Shifting; Repetitive Control.
因此，新型转子泵可以采用较普通转子泵更高的工作转速、更多的齿数，并获得更大的流量、更小的波动和更小的磨损。
So, this new type of cycloidal pump is capable of operating with higher rotation speed and more teeth, higher specific flow rate, less flow fluctuation and wear.
研究了由齿式联轴节联接的高速重载转子系统具有不对中时的频谱特征及其故障物理特性。
It is discussed that the high speed and heavy load rotor system connected by the gear coupling has spectrum characteristics and fault properties in the misalignment.
给出了定子螺旋面和转子蜗杆齿廓曲面方程以及行星轮轮齿滚珠与定子螺旋面及转子蜗杆之间的接触线方程。
The curved surface equations of the teeth profile on the stator helical surface and the rotor worm are given.
研究了由齿式联轴器联接的高速重载转子系统不对中时的动态特性。
It is discussed in this paper that the high speed and heavy load rotor system connected by the gear coupling has dynamics characteristics in the misalignment.
根据螺杆钻具转子加工时与铣刀的相对位置，建立空间螺旋齿面坐标系和铣刀坐标系。
According to the relative position of the rotor of the screw motor and the milling cutter, the coordinates of the helical tooth form and the cutter are-established.
以具体样机为例，分析了定子绕组匝数、永磁体充磁方向长度和转子外形对转矩特性的影响。分析结果表明：永磁体宽度接近于整数倍定子齿距可降低负载脉动转矩；
Take the sample motor for example, it is analyzed that the influence of the stator winding turns, permanent magnet width and the rotor shape on the torque performance.
最后，动力通过与齿型驱动轮适应的同步齿型带传输给所述冲击式磨机的所述转子。
Finally, power is transmitted to the rotor of the impact mill by a synchronous sprocketed belt, accommodated by a sprocketed drive sheave.
齿轮泵转子的齿廓型线一般为渐开线，渐开线型线虽设计加工方便，但存在原理性的困油现象；
The tooth profile of gear pump is involute in general. Though the involute profile is easy to design and manufacture, it also brings the inherent problem of oil trapping.
通过光弹实验表明了端齿连接转子受力的分区循环对称性。
The partially cyclic symmetry of the displacement and stress field in a typical rotor with curvic couplings is shown by carrying out a photoelastic experiment for the rotor.
为保证转子运转平衡，换齿时应注意成套更换，换后应做静平衡试验，以使磁选机工作稳定。
To ensure that the rotor operation balance, change gear should pay attention to the complete change, change should be done after the static balance test, in order to make separators stable operation.
在齿频误差中，分析了齿形误差、压力角误差和螺旋线波度误差激振下，转子系统的非线性振动特性，并与按线性模型计算的结果进行了对比。
Of all the gear frequency errors, the non-linear dynamic characteristics of gear tooth error, pressure angle error and sprial fluctuation error are compared with the results of the linear system.
本发明系一种圆弧齿摆线转子式发动机的结构。
The invention provides a circular arc tooth cycloid rotor-typed engine structure, in particular to a circular arc tooth cycloid rotor engine.
当空气充满整个齿沟时，转子之进气侧端面转离了机壳之进气口，在齿沟间的空气即被封闭。
When the air fills the entire tooth ditch, air admission of side end surface extension the rotor has left air inlet of the cabinet, namely is sealed up air in the tooth ditch's between.
当空气充满整个齿沟时，转子之进气侧端面转离了机壳之进气口，在齿沟间的空气即被封闭。
When the air fills the entire tooth ditch, air admission of side end surface extension the rotor has left air inlet of the cabinet, namely is sealed up air in the tooth ditch's between.
应用推荐