回想一下，B3字节覆盖路径开销和有效载荷部分。
Recall that the B3 byte covers the path overhead and payload section.
最短路径开销应按照输入的邮递路线的相应顺序输出。
The minimal tour costs should be output in the order corresponding to the input postal routes.
因此，这种情况，失误增多，其中B3仅表示，无论在本地或远程路由器接口腐化的路径开销或有效载荷。
Thus, a condition in which B3 errors increase only indicates that either the local or remote router interface corrupts the path overhead or payload.
这个数字产生通道接口接受的解决办法，因为（例如）在STS - 3的每个STS - 1的路径开销和B3字节。
This number produces acceptable resolution for a channelized interface because, (for example) each STS-1 in an STS-3 has a path overhead and B3 byte.
尽可能减少远程调用的数量，以减少由于代码路径中的远程调用带来的系统开销。
Minimize the number of remote calls to reduce the overhead imposed by remote calls in your code path.
这还是要归因于反射调用中的额外开销、较长的代码路径和跟踪活动。
Again, this can be attributed to some additional overhead in reflective invocation, a longer code path, and the tracing activity.
然而，如果读操作远远超过写操作，您可以结合使用内部锁和volatile变量来减少公共代码路径的开销。
However, if reads greatly outnumber modifications, you can combine intrinsic locking and volatile variables to reduce the cost on the common code path.
对应输入的每条邮递路线，应输出访问其所有街道至少一次的最短路径的开销。
For each postal route the output should consist of the cost of the minimal tour that visits all streets at least once.
要研究的方面包括：服务路径代价、CPU资源使用、应用级消息数量(由路径建立过程产生的消息开销)。
The aspects studied are service path cost, CPU resource usage, and number of application-level messages incurred by the path building processes (message overhead).
检查穿过路由组连接器的所有可行路由路径，然后选择具有最低总开销的路由路径。
Examine all possible routing paths across routing group connectors and select the routing path that has the least total cost.
已有的服务组合服务发现方法并没有考虑所发现执行路径需要的开销和服务的执行情况。
However, existing solutions fail to consider the overhead incurred by exploring the execution path and the condition of service execution.
方法尽可能地减小探测器在内核控制路径上的开销，适用于各种不同的环境。
This method decreases probe's overhead in kernel control path as far as possible, so it is applicable to various context.
在移动主机切换链路的时候，中转代理起到缓存的作用，可以减少所需要更改的路径的节点数量，同时减少切换开销。
The transmit agent acts as a buffer when the mobile node goes handoffs and reduces the overheads as same as the number of the hosts along the changing road which need to change.
仿真实验表明，MQAR协议在保持较高的报文传输率的情况下，有效地减少了路径建立时间和修复时间，大大降低了路由开销。
The simulation results show that MQAR protocol can effectively reduce route establishing time, route recovery time and routing overload as well, and the packet delivery ratio remains high.
现在的互联网络应用大多是使用单路由协议，数据采用单路径方式进行传递，由于数据沿着一条路径传输，路由开销和网络延迟较大，在负载较大的时候容易引起拥塞。
Currently, Internet routing protocol is single path routing, data transmits along a single path, this will bring large routing overhead and the network delay, and also will cost congestion easily.
只有当两条路径都中断，源节点才重新进行路由寻找，从而减少路由寻找次数，降低了路由控制开销。
Only when the two links broken, the source nodes restart to find new routings. So it decreases the number of routing seeking to reduce routing overhead.
只有当两条路径都中断，源节点才重新进行路由寻找，从而减少路由寻找次数，降低了路由控制开销。
Only when the two links broken, the source nodes restart to find new routings. So it decreases the number of routing seeking to reduce routing overhead.
应用推荐