行程调节：轻松访问行程调整螺钉准确运输中风。
Stroke Adjustment: Easy access stroke adjusting screws for exact carriage stroke.
检查定位标是否对零线：将重锤放下观察定位标上刻线是否与零线重合，有偏差时可调整定位标两侧的螺钉。
Ensure that the height marker is on zero graduation: Fall down the cylinder to check, if any deviation, adjust the two screws of the height marker.
高速配气机构设计中一个不可忽视的薄弱环节是气门间隙调整螺钉头部的挤压疲劳。
The squeezing stress between the valve end the screw for adjusting valve clearance must be taken into account in designing high speed valve train.
螺纹长度可调整的圆头螺钉的侧面图。
螺纹长度可调整的翼形螺钉的侧面图。
螺纹长度可调整的半埋头十字槽螺钉的侧面图。
Side view of raised countersunk posidriv screw with adjustable thread length.
螺纹长度可调整的平头一字槽螺钉的侧面图。
Side view of square head bolt with adjustable thread length.
柴油机横臂导杆折断会带来严重后果，经分析认为其折断原因有：同名气门杆顶部不齐；调整螺母松动，调整螺钉窜动；气门导管与气门杆间隙量大。
The reasons are: different top heights of valve rods having the same names; loose adjustment nuts or adjustment screws moving; and big clearances between valve guides and valve rods.
本实用新型涉及一种超平尺，它由：调整螺旋杆、固定托、螺钉、超平板、超平尺、水平标、支架构成。
The utility model relates to a super flat ruler which is composed of adjusting screw rods, a fixed support, a screw, a super flat plate, a super flat ruler, a horizontal scale and a bracket.
介绍了一种自行研制的装配专机，适用于汽车“盖板总成(预装配)”中将“调整螺钉总成”拧进“盖板总成”的装配工序。
This paper presents the customized equipment suitable to screw "adjusting bolt module" in "cover sheet assembly (preassembly)" for automobile assembling process.
但骨质疏松患者容易出现螺钉松动和复位矫正丢失、螺钉翻修或者重新调整螺钉位置后螺钉的稳定性较差。
But loss of correction and screw loosening often occurs in patients with osteoporosis, or screw has less stability in revision surgery and re-adjust of screw position.
将仪表安装到测量位置上，接通电源，通过表壳体上标牌下的调零、调满螺钉对零点和满度进行调整。
After installation and supplying power, you can adjust the Zero and full scale according the label on the housing.
该离合器由离合器本体、本体支承轴承、钢珠座、钢珠、导柱、弹簧和调整螺钉组成。
The clutch is composed of a clutch body, a support bearing of the body, a steel ball seat, a steel ball, a guide column, a spring and an adjusting screw.
可通过两侧端盖上的调整螺盖来进行，调整前应松开紧定螺钉，调整后拧紧。
It can be adjusted by the adjusting screw caps located on the head covers of both sides. Loose the locking screws beforehand, then re-tighten them after.
减压器上设有出气压力调整螺钉，通过调整出气压力螺钉来调节喷气阀所需求的工作压力。
Adjusting screw for outlet gas pressure is set on reducer; it can adjust working pressure for requirements.
如果量规（此处应该就是“压力表”）读数过高，将制动螺钉顺螺线方向放松； 如果量规读数过低，则向相反方向调整制动螺钉。
Loosen the clamp screw(s) and move slightly toward the helix if gage is reading high. and away if reading low.
给予调整。拧紧所有螺钉。
给予调整。拧紧所有螺钉。
应用推荐