它还允许配置应用程序的负载平衡器和自动伸缩功能，后者是控制水平节点的选项。
It also lets you configure your application's load balancer and auto scaling, which is the option that controls horizontal nodes.
对于DS4800，当创建一个逻辑列时，它自动将控制器所有者设为用于负载均衡的优先路径。
In the case of DS4800, when creating a logical volume, it automatically alternates controller ownership as the preferred path for load balancing.
自动请求流管理器(ARFM)提供对传入工作负载的流控制。
Autonomic request flow manager (ARFM) provides flow control for incoming workload.
自动检测系统由可控电子负载及其控制设备组成，可以对电源系统的负载均衡程度等关键指标进行实时检测。
Automatic detection system by controllable electronic load and its control equipment, power can be key indicators such as level of load balancing system for real-time detection.
自动电源控制，频率自动调整负载平衡，使其更为灵活和稳定，建立大规模的网络。
Auto power control, frequency auto-adjustment and load balance make it more flexible and stable to establish large scale network.
采用智能化控制系统自动调节滚筒高度及牵引速度，使采煤机负载趋于平滑。
The drum height and haulage speed both are adjusted automatically by using intelligent controlled system to make the load of cutter smooth.
介绍变频器驱动一用一备负载的自动定时轮换控制电路及组合开关联接。
This paper introduces the automatic control circuit time in turn driven by inverter with the using and the reserved load and combined switch connection.
电力系统一般都很复杂且变量又多，实现二阶负载—频率自动控制也相应变得很困难。
Because power systems are complex and multi-variable, it is very difficult to realize automatic secondary load-frequency control.
每个拆卷机上，膜都是包裹在负载单元式卷轴上的，这样就能监测膜的张力，为电自动的闭环张力控制器提供反馈的信号。
At each unwinder the film wraps around a load-cell-mounted roller, which monitors the film tension, providing the feedback signal for electronic automatic closed-loop tension control.
电力线载波技术分为两类，一种是用于负载控制、远程抄表和家电自动化的低速电力线载波通信。
There are two kinds of Power Line Carrier technology. One is used for Load Control, Remote Meter Reading and Home Automation, which is a short rate application.
控制器根据负载变化情况，自动调节行走速度实现功率自动分配，以充分利用发动机功率保证作业质量。
The controller adjust travel speed automatically according to load condition to realize automatic power distribution, so that operation quality is guaranteed via fully utilizing engine power.
介绍了具有缺相保护的双负载-双电源的自动切换控制。
This paper described the automatic switch control system of double-load and double-supply with the function of phase-lack protection.
使用：接好电源、负载及热电阻线后，按下温控器电源开关，温控器即可自动投入定温控制运行。
Operation: Once get power supply, loads and thermal resistors connected, press the power switch of temperature controller, and then it will start temperature control program automatically.
样机运行结果表明，控制系统能随外部干扰和负载变化自动跟踪谐振频率，并有可靠性好，电路简单，抗干扰能力强的特点。
The prototype operation indicate that control system can automatically adapts the drift of parameters with the new wethod. It has such character as high reliable, simple circuit and good anti-jamming.
本文提出了负载自动适应的减张力液压卷取系统的概念，对其结构及液压控制系统进行了设计，同时对系统的卷取性能进行了仿真。
In this paper, a hydraulic pulling-winding system with load auto-adaptation is put forward. The structure and hydraulic control system are designed, and its winding performance is simulated.
介绍了一种用于多传动点，带同一负载时控制传动点电机负荷分配的装置。该装置在多传动点负荷分配上实现了自动检测、自动控制、故障警示等自动功能。
A device which is used to control load distribution of the multipoint drive is presented. It has some functions such as automatic check, control, fault warning etc.
该装置由NAJS全自动极速多台位互感器检定装置、电流负载箱、控制柜、电流互感器专用测试台等几个部分组成。
The device consists of NAJS automatic flash speed multi-position transformer calibration device, the current load box, control cabinet, current transformer test stand and other components.
该装置的柴油机及燃气轮机功率、转速及负载转换控制、自动同步离合器的动态性能指标等是影响舰船机动性和操纵性的重要因素。
The dynamic performance of Synchronous-Self-Shifting clutch is of great importance to the control on transmission of power, rotation speed and load.
起动控制由起动器根据电机的转速自动完成，彻底避免了其它起动装置不能根据负载的大小，自动跟踪电机起动过程而造成电机或起动器损坏等不良现象。
It avoids the phenomena that some damage to motor and starter from other equipment can not trace the starting process of motor by overload.
在该电源的输入与负载之间连接了一只阻抗器，通过接入反馈控制网络自动调整阻抗器的电阻值，即可稳定输出电压。
A impedor is connected between the input and the load. The impedor is automatically adjusted by linking feed back loop for the purpose of stabilizing the output voltage.
在该电源的输入与负载之间连接了一只阻抗器，通过接入反馈控制网络自动调整阻抗器的电阻值，即可稳定输出电压。
A impedor is connected between the input and the load. The impedor is automatically adjusted by linking feed back loop for the purpose of stabilizing the output voltage.
应用推荐