打磨焊缝表面缺陷或机械损伤后的厚度小于母材的厚度。
Seam surface defect after grinding or thickness is lower than base material after mechanical treatment.
这种木材差不多是头等材，但它还有些缺陷。
This timber approximates first-class standard, but it still has some defects.
分析钛材管道焊接产生的冷裂纹、气孔、氧化等缺陷的原因和形成机理，提出焊接工艺措施，以确保焊接的质量。
And analyzes the reason and forming mechanism of the defects such as cold crack, air porosity and oxidation etc. proposes the measures of welding process to ensure the welding quality.
皱褶是铝及铝合金带材生产中常见的缺陷，介绍了我公司带材退火过程中产生的皱褶，该缺陷形成的原因及其预防措施。
Rumple is the familiar defect during the producing of aluminium & aluminium alloy strip. This article introduces a sort of rumple producing during anneal, discusses causes and preventive measures.
随搅拌头转速增加，断口处缺陷明显减少，对强度影响不显著，接头强度可达母材的84%。
Therefore, the effect of the defects on the strength of the joints was significantly reduced, and a joint efficiency of 84% was obtained.
对板带材表面缺陷图像的识别与分类进行研究具有重要理论及经济价值。
The board strips surface defects inspection and classification can dedicate not only to the theory but also to the economical values.
实验结果表明：这五种阔叶树材干燥特性差异显著，其中椆木干燥缺陷严重，干燥速度缓慢；
The results of the experiment showed that the differences among the five species are obvious. The drying defects of Lithocarpus glaber were serious and its drying rate was slow;
详细分析轧制过程中带材内部残余应力产生的原因，以及由残余应力造成的板形缺陷。
The paper explains the reason why residual stresses is produced in the strip when rolling and the flatness fault caused by residual stresses.
文中论述了棕榈藤各种藤材存在的主要缺陷，并讨论了藤材的分级标准和工业用藤的规范。
This paper discusses the main defects, classification standard and industrial specification of rattan cane and its derivatives.
本文综述了清除铸锭表层缺陷，以提高挤压材表面质量的方法。
The methods to improve the quality of the surface of extrusion materials by removing the defects on the surface layer of casting ingot are reviewed in this paper.
结合眼镜用异型钛材的生产实际，探讨了冷轧裂纹缺陷的形成原因，并提出了防止裂纹产生的有效措施。
According to the production practice, the article probes into the causes of cold rolling cracking of Titanium material for eyeglasses and puts forward effective measures for preventing the cracking.
控制亚麻油地材分层、鼓包、起壳等缺陷，是使用此装饰材料质量控制的重点。
It is an emphasis of the decorating material quality control to control the layering, bag swelling, protuberance shell and other defects of the flax oil floor material.
控制亚麻油地材分层、鼓包、起壳等缺陷，是使用该装饰材料的质量控制重点。
It is an emphasis to the decorating material quality control, which is to control flax oil floor material's layering, bag swelling, protuberance shell and other defects.
该文对钛材焊接时易产生的缺陷做了较详细的论述和分析，并提出了较全面的防护措施。
In this, article the defects easy occurred in titanium welding were mentioned and analyzed in detail. The comprehensive prevention was put forward.
另外介绍了母材缺陷分层、夹杂物、带状组织对ERW焊缝的危害性。
In addition, it is introduced that the layer, impurities and band structure in base material are harmful to the weld quality of ERW steel pipe.
另外，轧材内部存在缺陷也能促进剪切撕裂的形成。
In addition, the inner defect of the rolled material can also produce the formation of the shearing splitting.
在试生产中暴露出棒材输送方式存在缺陷，针对问题进行分析、探讨，并加以改进。
There occurred some problems in the transportation mode of bars during the trial production. The problems were analyzed, discussed and improved.
近年来卡式瓶的出现较好地解决了安瓿瓶作为注射剂内包材的缺陷，可以代替安瓿瓶作为注射剂的内包材。
The recent appearance of portable bottle can solve this problem well, which, then, can be used to replace ampoule bottle as the inner package of injection.
轧辊表面缺陷检测是轧辊辊型在线检测系统中的一个重要问题，它直接影响着带材产品的质量，传统的检测方法和数据分析方法已经很难适应现代的轧制生产。
Detection of roller surface defect is an important question in the roller profile online measurement system. It has direct effect on the quality of the strip steel products.
试验过程电弧燃烧稳定，焊接接头充分熔透，母材与焊缝连接良好，未见气孔、裂纹等缺陷。
The tests show: there are steady arc burning, fully fused weld joints, good connection between base metal and weld joint, no air bubble, cracks etc.
另外，轧材内部存在缺陷也能促进剪切撕裂的形成。
In addition, the inner defect of the rolled material can also prod...
挤压棒材表面质量良好无裂纹等缺陷，棒材中增强体颗粒和基体界面结合良好，基体合金中存在完整的等轴晶。
The surface of extrusion bar was of good quality without cracks. The interface between the particle and matrix bold was well and fine grains existed in the matrix.
我国目前人工林本材材质差、缺陷多，主要表现在强度低、尺寸稳定性差。
The timbers of our country man made forest have poor quality and some defects, which indicate their low strength and unstable size.
我国目前人工林本材材质差、缺陷多，主要表现在强度低、尺寸稳定性差。
The timbers of our country man made forest have poor quality and some defects, which indicate their low strength and unstable size.
应用推荐