检查(泥浆)泵缸套和活塞。
许多工艺因素对高磷风冷缸套质量有影响。
There are many process factors influencing the quality of the air-cooled high phosphorus cylinder liners.
主要有两种类型的气缸套：干缸套和湿缸套。
检查一下缸套和活塞。
白斑是离心铸造厚壁铸铁缸套的一种异常组织。
The white spot defect is an abnormal structure generally found in large cast iron cylinder sleeve by centrifugal casting.
工业有冶铁、化肥、炼焦、纺织、水泥、缸套等。
Metallurgical industry, chemical fertilizer, coke, textile, cement, liner and so on.
采用的顶置湿缸套技术，降低机油耗、提高可靠性。
With overhead wet cylinder liner, oil consumption is reduced and reliability is improved.
对近几年来发表的浮动缸套测量法进行了分析和评述。
Analysis and comment are made on the floating cylinder sleeve method known in late years.
分析了柴油机缸套穴蚀形成原因、特征及其影响因素。
Analyses the formation reasons, common characteristics and influence factors of diesel engine cylinder bore cavitation.
泵的置有吸入阀和排出阀、泵缸、缸套和拉杆的一侧。
The side of a pump where the suction and discharge valves, pump cylinders, liners, and rods are located.
论述了钒钛铸铁柴油机缸套激光强化的工艺与组织特征。
Laser strengthening process and structure characteristics of VTi cast iron cylinder liners in diesel engine are discussed in this paper.
系统地阐述了发动机缸套活塞组瞬态摩擦力的测量方法。
This paper introduces systematically the method for measuring the instantaneous friction force of cylinder liner-piston pair in the engine.
研究结果表明：采用激光硬化处理可明显提高缸套的硬度。
The study indicates that using laser hardening can remarkably improve the hardness of cylinder.
结果表明，该方法在活塞-缸套磨损诊断中是行之有效的。
The result indicates that the method is effective in the fault diagnosis of piston-liner wear condition.
缸体：龙门式、不镶缸套、水泵涡壳等零件都铸在缸体上。
Cylinder block: Dragon door style cylinder block without liner and with water pump turbo house resisted.
缸套穴蚀主要是由机体的高频振动和冷却水的高压冲击而引起。
Cavitation erosion is caused by high frequency vibration of engine body and high pressure impulse of coolant.
实例表明，该方法能够有效地诊断出柴油机活塞缸套的磨损故障。
Actual applied instance indicates that this method can effectively diagnose the faults of piston-liner wear.
按苏联标准测取不同的缸套直径时，得出的配合间隙值也各不相同。
According to the standards of USSR, the clearance is different if cylinders with different diameters are chosen to be measured.
本文研究了45钢抽油泵缸套激光热处理后的显微组织和硬度的变化。
Treated with laser the changes in microstructure and hardness of cylinder sleeve of oil-well pump for 45 steel were studied.
为了提高硼铸铁缸套的耐磨性能，对硼铸铁气缸套进行激光熔凝处理。
In order to improve the wear performance of boron cast iron cylinder liner, the laser remelting process has been used.
试验表明，钻井泵泵阀和缸套经增碳-钒化处理后其使用寿命显著延长。
Test shows that the service life of the drill pump valve and liner after carburizing and vanadiumizing are greatly extended.
该方法能够更好地改善缸套和活塞环的润滑性能并能提高缸套的表面硬度。
It can improve the lubrication performance between cylinder liner and piston rings and enhance the rigidity of cylinder wall farthest.
针对这一问题，提出了利用柴油机缸套水对原料空气进行加热的改进方案。
Therefore propose an improved plan, use the water of cylinder diesel engine heating air.
本文主要介绍对已完成基本结构设计的气缸缸套精磨外圆夹具的有限元分析。
This text mainly introduces a way of Finite Element to analysis the fine whetting outside circle of urn about the tongs.
选择柴油机缸套—活塞副运行工况中的磨损状态和磨损超限状态进行了研究。
The wear state condition of diesel cylinder-piston pair was studied, and the monitoring of cylinder-piston pair under the extreme condition was discussed.
从理论上对多缸内燃机缸套活塞系统摩擦学与动力学的耦合问题进行了研究。
The coupling problem between the dynamic behaviors and the tribological behaviors of the piston-liner systems in multi-cylinder internal combustion engines was studied.
为了实现船舶主柴油机的变流量冷却，需要对主机缸套冷却水系统进行水力计算。
Three-way regulating valve is currently used to control the temperature of cooling water in jacket cooling water system of main marine diesel engine.
为了实现船舶主柴油机的变流量冷却，需要对主机缸套冷却水系统进行水力计算。
Three-way regulating valve is currently used to control the temperature of cooling water in jacket cooling water system of main marine diesel engine.
应用推荐