该断路器通过拨码开关完成整定电流、脱扣时间、瞬动倍数等参数的设定。
Through dial switches the circuit breaker can set rated current, tripping time, instantaneous multiple and so on.
空气线路断路器空气线路断路器的功能是当电流大小超过断路器的过流跳脱设定值后自动断开。
Air circuit breaker An air circuit breaker automatically interrupts the current flowing through it when the current exceeds the trip rating of the breaker.
该电路具有既能将负载电流限制在设定值以内,又能控制限流工作时功率管的开关频率等特点。
This circuit has both characters of restricting the current within the giving value and limiting the switching frequency of MOSFET operating on current limited condition.
热继电器的设定值应能在不超过压缩机额定电流的140%时断开。
Thermal relay value should be able to in no more than 140% of the rated current compressor when disconnect.
同时配备缝焊控制器,对焊接时间,间歇时间,焊接电流能精确的设定和控制。
Equipped with welding controller, the welder has precise control and setting functions for the welding time and intervals and welding current energy.
这电源电流可设定使用一个电阻的i调节脚。
This supply current can be set using a resistor on the I ADJ pin.
注:常规出厂的CM 2 Z四极断路器中性极电流值符合表二,用户也可自行100%保护设定。
Note: Normally, current values of neutral pole of CM2Z four-pole, conform to table two, and it can be setted by users with 100% protection.
如果使用中电流超过了设定点,会有90分贝的警告声响起。
A 90-db horn sounds an audible warning if this current set point is ever exceeded during use.
这些特征数据用于提供设定点对目前的离子电流比较值。
These characteristic data are used to provide set point values against which the prevailing ion current is compared.
只要预先设定好胶合电流值和时间,本系统会根据电流的反馈信号自动调节,胶合电流不会受到厚薄的变化和模具温度上升的影响。
As long as the pre-set current value and a good bonding time, the system based on current feedback signal auto - Regulation, will not be glued current thickness change and mold temperature rise.
通过参数设定、输入电压相位计算、控制算法实现和开关接口等环节设计,实现了输入电流偏置角动态调整的控制策略。
In order to study the strategy of input current modulation, the simulation model of matrix converter under unbalanced input is built with MATLAB.
恒流方式时要求不论输入电压如何变化(在一定范围内),流过该电子负载的电流恒定,且电流值可设定。
Constant current mode, regardless of the input voltage required to change (within a certain range), flows through the constant current electronic load, and the current value can be set.
条件允许实时读数的电压,电流,功率和故障,并实时改变设定点调整的权力,工艺要求。
Allows for real-time readings of voltage, current, power and fault conditions, and for real-time changes to the set point that adjusts power to process requirements.
可以设定电流,自动检测集电环两个电极在一定电流下的电压降,并且还可以检测集电环与轴之间的绝缘电阻及漏电流。
It can be used to set current, automatically detect the voltage drop of the two slip ring electrodes in a certain current, and the insulation resistance and leakage between the slip ring and the axis.
电流在反馈电阻上产生的电压超出设定值时,IR 2132启动内部保护电路,关断输出通道,实现电流保护。
When the voltage on the feedback resistance over the designed value, the inside protection circuit was operated and the output channels were cut in IR2132 to achieve current protection.
生产线运行速度通过触摸屏设定,变频器的运行频率、电流及所有设备的运行状态均可在触摸屏显示。
The running speed of the production line can be set by the touch screen, and the inverter frequency, electrical current and the running states of every equipment will be showed in the screen.
它只需一只外接电阻就可设定所需的电流值。
Current is established with one external resistor and no other parts are required.
本文通过对电子、电气设备安全标准的理解和耐压试验的工作实践,对试验中存在的判定电流设定、升压速度控制、耐压试验结果判定和设备性能要求等问题进行了探讨。
Based on the understanding to the safety standards of electronic and electrical equipment and on the practice, this paper discussed the issues on setting the trip current, speed of rising H.
偏压电路依据参考电压来偏压第一级电路与电流补偿电路,并设定电流补偿电路的偏压。
Bias circuit according to the reference voltage to bias the first stage circuit and the current compensation circuit, and set the bias current compensation circuit.
本发明公开了一种设定背光模块的驱动电流的方法,包含:将该背光模块安装于一底座;
The invention discloses a method for setting drive current of a backlight module. The method comprises the following steps of: mounting the backlight module on a base;
由于新开发的A /D转换器允许任意积分时间设定, 7461A是理想的平均测量的脉冲电流和电压的移动电话和显示器生产商。
Since the newly developed A/D converter has allowed arbitrary integration time setting, the 7461A is ideal for average measurement of the pulsed current and voltage of mobile phones and LCDs.
预定电流可以设定为对应于最大亮度的像素电流。
The predetermined currents may be set equal to pixel currents that correspond to a maximum brightness.
系统能设定提供给电解水装置的电流大小,并使其无论在温度或水量变化的情况下,始终能恒定提供所设定的电流。
System can set the device to provide water to the electrolysis current size, and make both changes in temperature or under water, and always able to provide the constant current setting.
主要解决无法实现对设定电流的快速动态跟踪和对实际起动过程参数、起动效果及起动设备的状态无法实施实时监控及自动记录功能的问题。
It is designed for the unrealization of quick dynamic tracking of the set current and real-time monitor and automatic recording of actual starting process parameters, effects and equipment status.
当充电电流在达到最终浮充电压之后降至设定值的1/10 时, EMC5040将自动终止充电循环。
The EMC5040 automatically terminates the charge cycle when the charge current drops to 1/10th the programmed value after the final float voltage is reached.
当充电电流在达到最终浮充电压之后降至设定值的1/10 时, EMC5040将自动终止充电循环。
The EMC5040 automatically terminates the charge cycle when the charge current drops to 1/10th the programmed value after the final float voltage is reached.
应用推荐