热辐射：受热表面发射能量的过程。
Thermal radiation: Process by which energy is emitted by a warm surface.
洗涤剂，以击退残留物形成的热表面。
Detergents are made to repel residues from forming on hot surfaces.
注意：请勿接触发热表面。
粉尘层可以点燃的热表面。
热表的流量参数包括额定流量及最大、最小流量。
Table heat flow parameters including rated flow and the largest and smallest flow.
折痕角度越大，吸热表面积越大，也可以折叠的更快。
Wider hinges also fold faster, because there is more surface area to absorb energy.
人员易接近的热表面和冷表面应作标记或加以机械防护。
Hot and cold surfaces that are accessible to personnel should be identified by sign or mechanically guarded.
石脑油馏份与一个热表面接角，就裂解而得到乙烯和丙烯。
In contact with a hot surface, naphtha petroleum fractions crack to produce ethylene and propylene.
对中频感应加热表面淬火在弹簧生产中的应用进行了实验研究。
This article is about the application of mid-frequency induction heating to spring production. We have many researches and experiments on the technological process.
这种改进型处理能力的关键是降低了热表面与转换装置之间的间隔。
A key to the improved throughput was reducing the separation between the hot surface and the conversion device.
图示为圆盘传送带加热表面，这样材料就能够尽可能地被均匀加热了。
Carousel heating furnace where the materials get heated as evenly as possible.
在蓄冷器工厂中，因为加热表面是石头提供的，所以腐蚀问题较少。
The corrosion problem is less in regenerative plants since the heating surface is provided by stones.
也就是说，热量转移到它的物质接触烘干机的加热表面，干燥传导材料。
That is, the heat is transferred to the material as it contacts the dryer's heated surface, drying the material by conduction.
介绍了RM - H数字式智能型热表的原理、测试性能及试验运行结果。
The principle, testing performance and experience operation result of RM-H type digital and intelligent heat meter are introduced.
用热表面离子源测定了锂同位素丰度，在样品全耗尽过程中累计离子流强度。
The isotopic ratio of lithium was determined by cumulating intensity of ion current during evaporation of all samples on evaporation filament.
结果表明，通入空气使沸腾传热系数有所提高，并且加热表面温度有所降低。
It was found from the experimental results that air introduction can significantly enhance the boiling heat transfer and make the temperature of heated surface lower.
用这种方式向红热表面上喷涂导致得到的陶瓷与金属基底的粘结显著改善。
Spraying onto a red-hot surface in this fashion leads to a very marked improvement in adhesion of the resulting ceramic to the metal substrate.
这种情况下的接触热表面被认为是不太可能发生的，故烫伤的风险已降到最低。
A contact with the hot metal surface is not therefore likely. The risk of burning is minimized.
这对深化表面涂层强化冷凝传热的机理以及选择传热表面涂层材料具有指导意义。
It is of considerable significance to get more insights into the mechanism of condensation heat transfer enhancement by means of surface coatings.
对浸泡在强润湿性液体中的光滑传热表面的沸腾起始状态进行了实验及理论研究。
An experimental and theoretical study was conducted to investigate the incipient boiling condition of smooth heat transfer surface immersed in highly wetting liquids in the paper.
研究了带有同心套管的垂直圆柱形加热表面在环隙中通入空气时的核沸腾传热性能。
Nucleate boiling heat transfer on a vertical cylindrical heated surface with a concentric outer tube was investigated when air was introduced into the boiling liquid.
对水溶液中矿物质离子在换热表面的结垢过程及对换热性能的影响进行了实验研究。
It was showed that the surface and fluid temperatures were very important to promote fouling process on heat transfer surface.
对各种传热表面的板翅式紧凑热交换器进行了优化设计计算，建立了通用优化程序系统。
The design optimization is accomplished on all kind of plate-fin surfaces of compact heat exchangers and its general optimization program is set up.
对某种金属蜂窝平板进行了模拟气动加热试验，测定了加热表面和非加热表面的瞬态温度。
An aerodynamic heating simulation test was carried out on a metallic honeycombed plate and the transient surface temperatures of the heating and UN heating surface were obtained.
因此，热表的普及与使用对节约能源、控制污染等都具有深刻的现实意义和长远的战略意义。
Therefore, the spread and use of heat energy meter has important practical and long-term significances in many aspects such as pollution control etc.
建立了纤维湿热表面涂覆的数学模型及衡算方程，讨论了其在项目设计和工程应用中的适应性。
The mathematical model and calculation equations of wet-heat surface coating for fibers was established. The applicability of the model was discussed for project design and engineering application.
强化传热表面在工业换热设备中具有广泛应用，其表面状况对于传热与结垢过程均有重要影响。
Enhanced surface was used in heat transfer equipment widely, and the surface condition has an important influence on the fouling process.
通讯总线是一种欧洲标准的仪表总线通讯格式，是为了远程读取热表而制定的一种新的欧洲标准。
The M-Bus bus is a kind of communication format of Meter bus, is the New European standard for remote installation data readout system.
通讯总线是一种欧洲标准的仪表总线通讯格式，是为了远程读取热表而制定的一种新的欧洲标准。
The M-Bus bus is a kind of communication format of Meter bus, is the New European standard for remote installation data readout system.
应用推荐