您可以将合适的命令与所有参数和标志放在一起。
You could put together the proper command with all of the arguments and flags.
您可以将合适的命令组织在一起,并使用各种参数和标志,然后在每个系统中运行它们。
You could put together the proper command, with all of the arguments and flags, and then run that on each system.
如果使用的是其他发布版,一些命令名和标志可能需要更改。
If you are using another distribution, some of the command names and flags may change.
下面的表2介绍了接口标志和一些属性检索命令。
Table 2 below shows interface flags and some attribute retrieval commands.
EFS命令标志和选项的完整列表,请参见参考资料部分。
For complete list of flags and options of EFS commands, see the Resources section.
一般而言,当你运行命令行程序时,可以把把这些当做输入,像什么参数啊,或开关啊,或标志啊等等。
So in general, when you're running command line programs, they can take input or arguments or parameters or switches or flags.
例如,以下命令使用- u标志报告CPU统计数据。
For example, the following command using the -u flag reports CPU statistics.
此命令实际上就是将选择作为其标志的积累活动的内容写入到标准输出。
This command essentially writes to standard output the contents of the cumulative activity, which you would have selected as its flag.
一些人喜欢使用命令行执行带各种标志的命令,其他人喜欢使用 GUI和X窗口会话。
Some people prefer to use the command line to execute commands with all the flags, while others prefer GUIs and X window sessions.
在前一个示例中,这个命令标志生成了输出。
In the previous example, this command flag produced the output.
如果您使用- a标志运行ls命令,将会看到两个条目:一个是.(圆点),另一个是. .。
If you run the ls command using the -a flag, you can see an entry for. (dot) and another for..
把代理定义为可信应用程序的方法是在mqsicreatebroker命令中使用-t标志。
To define a broker as a trusted application, use the -t flag on the mqsicreatebroker command.
您还可以使用增强的extendlv命令的 -u标志,这样可以在一项操作中同时完成增大上限并扩展LV。
You can also use the -u flag of the enhanced extendlv command to raise the upper bound and extend the LV all in one operation.
要获取唯一系统标识符,可以使用带- Mu或- MuL标志的uname命令。
To get a unique system identifier, use the uname command with the -mu or -mul flag.
chauthent命令根据用户设置的标志设置所需的身份验证方法。
The chauthent command sets the desired authentication method based on the flags the user sets.
例如,想想从一个仅在Solaris上遇到的文件中提取信息的脚本;想像使用一个在Linux系统中不可用的标志执行一个系统命令。
For example, think about a script that extracts information from a file that is encountered only on Solaris; imagine executing a system command that USES a flag that is not available on Linux.
把可信代理改为标准方式的方法是在mqsichangeproperties命令中使用- n标志。
To change a trusted broker back to standard mode, use the -n flag on the mqsichangeproperties command.
修改现有的代理以使它成为可信应用程序的方法是在mqsichangeproperties命令中使用- t标志。
To modify an existing broker to make it trusted, use the -t flag on the mqsichangeproperties command.
所以,与在命令行上使用nwni标志不同,我们现在使用的是 nw,它仍旧限制Scilab 为命令行计算,但是加载图形库。
So, instead of using the nwni flag on the command line, you use nw, which still limits Scilab to command-line calculations, but loads the graphics libraries.
对比这两个命令的标志:您会注意到,padmin更为详细。
Compare the flags between these two commands: Note that padmin is far more verbose.
为了验证新创建的快照的状态,我使用- q标志运行snapshot命令。
To verify the status of the newly created snapshot, I ran the snapshot command with the -q flag.
当使用- M标志设置ltg大小时,如果磁盘的最大传输大小小于该LTG大小,那么varyonvg和extendvg命令可能会执行失败。
When the LTG size is set using the -m flag, the varyonvg and extendvg commands might fail if an underlying disk has a maximum transfer size that is smaller than the LTG size.
在AIX5lVersion 5.3中,通过varyonvg命令对其进行设置,并且使用- M标志。
In AIX 5l Version 5.3, it is set by the varyonvg command, using the flag -m.
您可以使用不带任何标志的标准df命令,进一步显示相关的信息(请参见清单14)。
You can further display the output information using the standard df command without any flags (see Listing 14).
基于更新的设计,为 /usr/bin/uname命令添加了两个新的标志,以便可靠地生成唯一系统标识。
Two new flags have been added to the /usr/bin/uname command based on the updated design to reliably generate unique system identification. These identifiers are for new hardware only
通过使用pwdadm命令,可以看出密码标志已经清除了。
We can tell that the password flags have been cleared, by using the pwdadm command, as described earlier.
新的AIX5lVersion 5.3uname命令标志。
uname命令标志输出-m、- u或- L并没有什么变化。
There are no changes to the uname command flag outputs, -m, -u, or -l.
Allowterminationofremote VM标志是一个开关,它确定调试器中是否支持Terminate命令。
The Allow termination of remote VM flag is a toggle that determines whether the Terminate command is enabled in the debugger.
在AIX5lVersion 5.2中,通过chvg或mkvg命令的- L标志来设置LTG大小。
In AIX 5l Version 5.2, the LTG size was set by the -l flag on the CHVG or MKVG command.
应用推荐