我希望我们在迎接挑战时能像挠曲试验机一样。
将这根金属线的末端向后挠曲。
区别尖锐的挠曲和断层更加困难。
A still more difficult distinction is that between a sharp flexure and a fault.
介绍了求变截面梁挠曲线方程的奇异函数法。
Singular function method is introduced to derive the deflection equations of beams of variable cross section.
框架结构的高阶模态表现为构件局部挠曲的模态形式。
High order modes of the frame structure represent the forms of member's local bending.
挠曲性能是玻璃纤维增强塑料夹砂管的重要性能指标。
The deflection level is an important performance index for FRP m pipes and should be specially.
分子量最小的第三种材料其挠曲强度和冲击强度都最低。
The molecular weight of the third material is the smallest, It's flexure strength and impact strength are low.
挠曲函数满足板的微分方程和全部边界条件、角点条件。
Flexural functions satisfy the differential equations of plate and all the boundary conditions as well as the conditions at free corner points.
在轴、外壳显现挠曲时，可以自动调剂，不增添轴承承担。
The shaft, shell buckling, can appear be automatic adjustment, not to increase bearing burden.
对充气展开管的弯折挠曲特性进行了理论分析和实验验证。
An theoretical analysis and experimental verifications are made to investigate the folding deflection behavior of inflated tubes.
模拟结果表明中国西部的岩石圈挠曲应力的量值达数百兆帕。
The result shows that the flexural stress of the western China is about several hundred MPa.
对框架柱进行了局部挠曲模态的脉冲激励试验和正弦稳态扫描试验。
Impulse excitation and sine stable sweeping tests of local bending modes of the frame columns were conducted.
分别以应力分析仪和显微硬度仪测试两组试件的挠曲强度和硬度值。
The flexural strength and hardness of the specimens were tested with an instron testing machine and a microhardness tester.
在光栅固定件中至少设置一个挠曲连接部，它允许基片热膨胀和收缩。
At least one flexure joint is provided in the grating mount which permits thermal expansion and contraction of the substrate.
某工程受横向荷载和轴压共同作用的楼面梁因施工缺陷发生初始挠曲。
Initial deflection of the floor beam of a project by lateral loads and co-axial role occurs because of the construction defects.
根据生产要求，限定最大许用挠曲度，即可确定相应的辊轮位置尺寸。
Restricting the maximum flexibility according topractical needs, then the maximum position of roller can be decided.
本文利用钻头不同位置不同方向的惯性矩和挠曲对其弯曲刚性进行解析。
This paper by means of different locations inertia moment of different directions and bending of the drill, analyses its bending rigidity.
机器人连杆的挠曲变形是引起机器人末端执行器位姿误差的主要因素之一。
One of the major fact ors affecting the pose accuracy of robot end-effector is the deflection of robot links.
它比天然橡胶具有较好的抗挠曲开裂性能，但撕裂强度较低，动态模量较高。
It has a better flex cracking resistance than those of natural rubber but a lower tear strength and a higher dynamic modulus.
由于局部挠曲和破裂的相互斗争，石板的冲击凿入载荷-侵深曲线为双驼峰形。
Because of the struggle between local bend and failure, the percussive fore-penetration curves have two peaks.
结论牙托粉的分子量和分子量分布对义齿基托的挠曲强度和冲击强度有较大影响。
Conclusion the molecular weight and the distribution of molecular weight of denture base powder obviously affect flexure strength and impact strength of denture base.
中生代构造快速沉降的沉积体的楔形展布表明盆地具有前陆岩石圈挠曲成因特征；
The Mesozoic rapid tectonic subsidence and wedge shaped sedimentary bodies indicate the origin of lithospheric flexure in the Chuxiong Basin.
广义叠加类型中除基本类型外还有限制型、展平残留型、叠加挠曲、共轴重褶等。
The restricted fold, the unfolded remaining fold, the superposed monoclinal flexures and the coaxial refolded type are in the generalized types.
它是在褶皱冲断带负载的作用下，岩石圈通过区域性均衡调整及流变挠曲而形成的。
They were formed through regional isostatic adjustment and Theological flexure under the load of fold-thrust belts.
由于轴的自重及水轮机转轮、发电机转子体的重量将使整个轴系的中心轴线产生挠曲。
The entire shafting center axes was bowed by axial self respect, weight of turbine runner and body of generator rotor.
文中采用门式刚架作为算例，分别研究了弹性、塑性及不同初始挠曲对其稳定性的影响。
With a door rigid frame as example, the influence is analyzed of elasticity, plasticity and different initial bending on stability of the frame respectively.
《材料力学》中出现的弯矩方程、挠曲线近似微分方程、挠曲线方程的定义域不尽一致。
The definition domains of the moment equation, the approximate differential line of deflection equation and line of deflection equation in Material Mechanics are quite different.
讨论了钢材的初始挠曲对钢混凝土连续组合梁的极限承载力与失稳屈曲临界荷载的影响。
The influence of initial displacement on load bearing capacity and critical load of steel concrete composite structure is discussed.
用这种方法可以分析多种外界因素对齿轮啮合的影响，如箱体变形、轴端受力、轴线挠曲等；
This makes it possible to analyze the effect on gear mesh of such factors as gear box deformation, axial end loading and axial deflection, etc.
用这种方法可以分析多种外界因素对齿轮啮合的影响，如箱体变形、轴端受力、轴线挠曲等；
This makes it possible to analyze the effect on gear mesh of such factors as gear box deformation, axial end loading and axial deflection, etc.
应用推荐