并对边界最薄处进行了强度校核。
And the strength check have been proceed toward the thinnest boundary.
根据分析结果进行强度校核和结构优化。
According to the analysis result, intensity inspection and structure optimization are executed.
最后进行了筒体静强度校核和疲劳强度校核。
Finally, the static intensity and fatigue intensity of the cylinder are checked.
通过强度校核,证明此种螺纹法兰安全可靠。
Strength check proves this threaded flange safe and reliable.
设计了典型零部件并进行了选材和强度校核。
The typical parts were designed and its materials were selected.
本文重点介绍了后悬挂缸的设计计算和强度校核。
This paper introduced the design calculation and strength check of rear suspended cylinder emphatically.
经过稳定性分析和强度校核,满足工程实际需要。
The practical requirements in construction may be met through the (analysis) on the stability and intensity of the system.
螺杆钻具挠性轴设计中的两个主要问题是强度校核和干涉量计算。
The main Problems with designing the flexible shaft on a screw drill are strength check and interference calculation.
石化管道应力分析中,二次应力的校核是最基本的强度校核之一。
In stress analysis of petrochemical pipe line, the secondary stress check is the one of basic strength check.
文章介绍了钢球连接方式火工装置中,钢球连接处的结构强度校核。
This paper relates to structural strength checking at a steel ball connection type initiating explosive device.
着重闸述了基本原理、叶片强度校核、作图方法及平衡检验的要求。
Emphasis is given to the fundamentals of design, check for blade strength, plotting procedures and the requirements for balance check.
同时采用了有限元的分析方法对其进行强度校核,结果满足强度要求。
Meanwhile, it applies the finite element analysis to make strength check, the result satisfies the strength requirement.
提出了一种钻柱强度计算新方法,可用于钻柱的强度设计和强度校核。
A new method for calculating drill stem strength can be applied to designing and checking strength of drill stem.
某框架结构综合楼由于新增设备,需要进行强度校核与抗震安全性鉴定。
Due to adding some equipments, intensity checking and seismic security appraisal need to be carried out for one frame.
硬面环和座环的强度校核和配合长度的确定也是镶嵌式动环设计的要点。
The intensity and matched length of hard ring and husk ring is also a designed key of mounted moving ring.
为室内程序疲劳试验谱、有限寿命设计谱和静强度校核提供了可靠的依据。
These results have been provided the essential data for programme fatigue testing and optimal design spectrum and static strength proof.
根据局部应力的理论分析,提出直立容器支承式支座处强度校核的新方法。
The introduces the new method for strength checking of vertical vessel bearing support based on theoretical analysis of local stress.
该系统能方便完成图表数据检索、齿坯设计、强度校核、绘图、调整卡计算输出。
The developed system can easily read data from graphs and tables, design hypoid gears, verify tooth strength, do drawings and calculate cutting and machine setting parameters.
运用最大应变能理论和强度极限分析法,对简体、端板等重要部件进行了强度校核。
Used the maximum strain-energy theory and strength limit analytic method to check the important part such as sleeve, end-plate, etc.
针对此脉冲风洞的基本结构,本文对风洞进行了强度校核,验证了风洞结构的安全性。
According to the structure of this tunnel, the strength is checked and the security of structure is validated.
用可靠性平均安全系数进行容器的强度校核比用常规安全系数进行容器校核安全和经济。
Checking up the strength of pressure vessels by average safety factors of reliability is safer and more economical than checking up the strength of pressure vessels by the conventional safety factors.
本文重点论述了环链式斗式提升机改造成板链式斗式提升机的过程及驱动轮轴的强度校核。
The paper reviews the process from ring chain type bucket elevator to plate chain bucket elevator and indicates the strength calibration of driving wheel axle.
在实验和分析的基础上,对工作在稳定状态下的转轴,提出一种简化可行的疲劳强度校核方法。
Basing on the experiments and analyses, it puts forward a simple and feasible method of checking the fatigue strength of revolving axle in a stable state.
通过对退锚器工作压力的确定、强度校核、合理计算,选择了活塞承压面积及各液压缸直径尺寸。
Through anchors identified by the work pressure, intensity degree, reasonable terms, choiced piston confined area and the size of hydraulic tank diameter.
因此采用大型有限元计算软件建立甲板局部结构模型,对系泊工况下甲板局部加强进行强度校核。
Therefore, we adopt finite element software to establish finite element model of local deck structure, calculate structure stresses and to check its strength.
研究了采煤机滚筒截煤时所受的载荷分布情况,提出了用于煤机零部件强度校核的载荷计算方法。
The paper studies load distribution status on shearer cutting drum while it works, puts forward load calculation method used for strength verification of parts of mining machine.
以480Q曲轴为例,进行了曲轴的疲劳强度校核,结果表明该曲轴能够达到增压后的强度要求。
Fatigue strength of the 480q crankshaft is checked and the result indicates that the crankshaft can reach intensity demand after boosting.
介绍了PW 200k型转向架空气弹簧复合座的结构特点,对该部件进行了改进设计和强度校核计算。
The structure features of the air spring on PW200K bogies are described. The design improvement and strength checking calculation are made for the part.
查阅和分析现有文献中给出的冲裁凸模强度校核公式,针对凸模抗压弯能力的强度校核问题进行了讨论。
Strength checking formula for blanking punch in current documents have been reviewed and the anti-bending ability of blanking punch is discussed.
采用有限元法对加氢反应器裙座支撑区进行有限元分析及优化设计,并对其危险截面作应力评定和强度校核。
The finite element method is applied to analysis and optimize the design of the hydrogenation reactor skirt support area, and stress of the risk section is assessed and strength is checked.
应用推荐