你仍然相信你是最好的未达到弹性极限。
You still believe that your best is not yet reached its elasticity limit.
疲劳强度低于弹性极限或屈服强度等静应力强度。
Fatigue strength is less than static stress strength such as elasticity limit, yield strength.
植被系统受到干扰后，会出现弹性极限与塑性极限。
Elastic limit and plastic limit appear after a disturbance to vegetation system.
通过对该实验数据的分析得到了圆筒的弹性极限压力。
The elastic limiting pressure of the cylinder was gained by analyzing the experimental data.
其目的是获得高的屈服强度，弹性极限和较高的韧性。
The aim is to obtain a high yield strength, elastic limit and high toughness.
但如果向它施加足够大的拉力，超过了它的弹性极限，该物体就会永久变形。
Apply enough force, though, and you will go past what is known as the elastic limit and the object will be deformed permanently.
采用该材料制造的抗侧滚扭杆具有高的疲劳寿命和高的弹性极限。
The side-rolling resistant torsion bar made of this steel exhibits high fatigue life span and elastic limit.
引起鼓包最根本的原因是带钢边缘延伸超出了该材料的弹性极限范围。
The root cause of this undesirable phenomenon is that the extension of the strip edge area is out of the elasticity limit of the material.
硅能显著进步钢的弹性极限，屈从点和抗拉强度，故普遍用于作弹簧钢。
Silicon can obviously improve the elastic limit, yield point and tensile strength of steel.
因此，要求钢具有高的弹性极限，高的疲劳强度以及高的冲击韧性和塑性。
Thus, requirements of steel with high elastic limit, high fatigue strength and high impact toughness and plasticity.
在到达其弹性极限之前，这种材料可被扭曲的程度大约是由它取代的钢铁构件的20倍。
They can be distorted about 20 times as much as the steel components they replace before they reach their elastic limits.
液压联轴器外套采用多层筒组合式外套可提高液压联轴器的弹性极限承载能力。
Using multi-layer assembled out sleeve can increase the utmost load carrying capability of a hydraulic pressure sleeve coupling.
建立钢-混凝土双面组合梁截面弹性极限和塑性极限承载能力的简化计算方法。
The ultimate bearing bending capacity of a double steel-concrete composite beam was also calculated by the simplified calculating method based on the elasticity and plasticity.
当材料不显示屈服点时，在进行设计计算中，往往使用所谓弹性极限这一数值。
When the material does not display a yield point, a quantity known as the proof stress is used when making design calculations.
装配式、整体式隧道横向变形处于弹性极限破坏状态，管片环横截面极限半径最大值、最小值。
The transverse deformation of entiretied and constructed tunnel are both in the elastic limit corruptstate, the solution of the maximum and minimum of the segments'cross-section radius.
在弹性极限以下的轻度干扰，植被系统受力后产生的应变可以通过植被本身的自组织能力得以自我修复；
The strain of a vegetation system can be rehabilitated by the ability of self-organization at the light disturbance which is under the elastic limit.
然后，继续增加力-，受到重力的影响，不断给它悬挂重量-，然后它开始弯折，到这里的某一点，我们称之为弹性极限。
And then, when you keep adding force — which we will do by gravity, - we will just hang weights on it — then it starts to bend over, up to a point here which we call the elastic limit.
当内外股分离给缆线材料所造成的压力操作了弹性极限后，易位或者不稳定的情况就会产生，进而造成永久的变形。
When this separation strains the cable material beyond its elastic limit, instability or birdcaging occurs in the form of the permanent deformation.
依据井壁围岩是否达到临界塑性状态而不是弹性极限状态来判断井壁稳定性是气体钻井井壁稳定分析模型的特殊之处。
The peculiarity of this wellbore stability model is to determine whether the wellbore rock is in the critical plastic state rather than elastic limit state.
本文利用库仑屈服准则，研究了拉压异性材料厚壁圆筒和厚壁球壳的弹性极限载荷和塑性极限载荷，得出了新的结果和结论。
This paper performs the limit analysis of a thick wall cylinder of linear strengthened material based on the unified strength theory.
某舰的螺旋桨尾轴长期处在恒定载荷作用下，虽然尾轴应力在弹性极限范围内，但是尾轴局部还是很容易发生微量的塑性变形。
Tiny deformation will appear in the local of the propeller shaft of certain ship which is endured an invariableness load, although the shaft stress is within the elastic limit range.
并对压力容器的弹性极限、塑性极限、金属内衬不会产生反向屈服的最大内压以及压力容器在“安定状态”下工作的条件进行了理论分析。
Elastic and plastic terminal of vessel, maximum internal pressure that metal liner can't be yielded in the opposite direction and basic condition that vessel works on stable state are presented.
拉伸载荷模量约等于比例极限内的弹性模量。
The tensile modulus approximately equal to the compressive modulus of elasticity within the proportional limit.
在此基础上计算了弹性无孔洞钢拱在不同荷载、不同约束、不同截面尺寸等条件下的极限承载力和顶点竖向位移。
Then the ultimate load-carrying capacity and the vertical top displacement of elastic steel arches are computed for different restrictions, different loads and different section sizes.
按规则设计，按分析设计，弹性应力分析，极限载荷分析，弹-塑性应力分析。
Design by Rule, Design by Analysis, Elastic Stress Analysis, Limit Load Analysis, Elastic-Plastic Stress Analysis.
每件东西都有弹性，但是，超过了一定的极限，它就会折断。
Everything has elasticity , but beyond a certain limit, it will snap.
由于钛的屈服极限与弹性模量的比值大，使钛成型时的回弹能力大。
Its resilience is strong during shaping, because titanium's ratio of yield limit to elasticity modulus is high.
由于钛的屈服极限与弹性模量的比值大，使钛成型时的回弹能力大。
Its resilience is strong during shaping, because titanium's ratio of yield limit to elasticity modulus is high.
应用推荐