如有必要,可以将负弯矩配置到承担一半以上的总弯距,这很适于使桥梁形成优美的曲线轮廓。
If desired, the hogging may be arranged to take more than half the total moment, which fits well with a graceful curved profile.
计算了结构与运动刚体之间的冲击力时程曲线、梁中的剪力及弯矩分布、轴力杆件中的轴力分布。
The impact force-time history between the structure and the moving rigid-body, shear force and bending moment distribution along the beams, axial force distribution along the bars were calculated.
以长桩结构能够承受的最大弯矩和吊点力不为负值作为限制条件,得出安全作业跨距和倾角参数控制曲线。
With the limitations of the maximal bearable bending moment and the positive lifting force, the controlling parameter curves of span and lifting Angle are then acquired to guide the safety operation.
除对使用荷载阶段进行研究和给出计算的结果外,也给出弯矩-曲率全曲线和极限变形的计算。
Besides the research and calculation materials for the stage of working load, the complete moment-curvature curve and the calculation of ultimate deformations are provided too.
结合双安全钳作用特点,以多跨度细长杆模型为基础,建立并求解了电梯导轨在复杂受力状态下的弯矩方程和挠曲线方程。
Based on the model of multi-span slender rod, the moment equations and deflection equations of elevator rail with duplex safety gear were established and resolved in a complex state of stress.
《材料力学》中出现的弯矩方程、挠曲线近似微分方程、挠曲线方程的定义域不尽一致。
The definition domains of the moment equation, the approximate differential line of deflection equation and line of deflection equation in Material Mechanics are quite different.
利用电子计算机对弯矩—曲率曲线全过程作了理论分析,并与试验结果进行了比较,两者比较接近。
The complete moment-curvature curves are obtained from theoretical analysis by using electronic computer, and they are almost in agreement with the experimental curves.
由于曲率的影响,曲线梁在其曲率平面内弯曲时的中性轴不通过横截面的形心。因此弯矩在形心处要引起正应力,从而引出所谓“等效轴力”的概念。
When a curved beam is bending in the plane of the curvature, the neutral axis of cross section is not identical with the axis of gravity due to the influence of the initial curvature.
本文通过对预应力混凝土屋架的荷载-挠度曲线分析,说明预应力混凝土屋架在强度极限状态时,屋架的挠度是不小的。因此,由屋架的变位引起的上弦次弯矩影响是不可忽略的。
Through the analysis of the load-deflection curves of prestressed concrete roof trusses, it is shown that these trusses deflect a considerable amount in the state of ultimate strength.
对框架组合梁,其弯曲屈服验算采用弯矩-曲率曲线验算;
Flexure yield of composite beam was checked by moment-curvature curve.
弯矩—曲率恢复力曲线可以是任意的,而相应的单元刚度矩阵的建立较为简单。
The type of hysteresis loops can arbitrarily be chosen, and the corresponding element stiffness matrix can be built up in a simple way.
在各弯曲试样得到不同的预应变后,又对其进行反向加载,记录不同预应变下各试样反向加载的弯矩随表面应变的变化曲线。
In these experiments, specimens were bending to produce different pre-strain respectively, and then reverse bending were taken one by one.
得到各种情况下组合梁界面滑移分布曲线及弯矩-挠度曲线,分析其变形性能。
The interfacial slip reduces the stiffness, increases deformation and influences performance of composite beams of steel and concrete.
得到各种情况下组合梁界面滑移分布曲线及弯矩-挠度曲线,分析其变形性能。
The interfacial slip reduces the stiffness, increases deformation and influences performance of composite beams of steel and concrete.
应用推荐