电阻封焊式金属外壳。
封焊后把管座清洗干净，然后把引线剪到所需长度。
After sealing the header is cleaned and then the leads are clipped to the desired length.
标准泵为离心式，或根据温度设定功率。极端温度下可使用磁力泵和无封焊水泵。
Standard pump designs are centrifugal type rated for the temperature range. For extreme temperatures, magnetic or seal-less pumps are employed.
用途：适用要求较高的微波器件，传感器，滤波器及航天，导弹上应用的元件气密性带压力保护的封焊。
Usage: suitable for air tight seal welding with pressure protection of microwave device, sensor, filter and components that used on spaceflight and guided missile that have high requirement.
如果阀体的材料是可以焊接的，但膨胀系数差异很大，或者工作温度的变化幅度范围较大，螺纹连接部必须进行蜜封焊。
If the valve body material can be welded, but very different thermal expansion coefficient, or changes in operating temperature range of a larger thread junction closure weld must be honey.
根据功能要求，本电气贯穿件的技术特点是采取了陶瓷组件封焊和钢管聚砜旋锻密封两种密封方法，以及紧凑的结构方式。
According to the functional requirements, their technical characteristics consist of two ways on seal, ceramic package seal weld and tube polysulfone whirl forge seal, and the compact structure.
本文介绍了空冷135MW汽轮发电机定子线圈的成型及封焊模具的设计。通过对线圈自身成型模的改进，可以同时在成型模上进行引线封焊。
This paper introduces the design of the mould for shaping and sealing braze of copper bars used in stator coils of 135mw aircooled turbogenerator.
传统的线圈成型模只能成型线圈的端部形状，而该装置在此基础上增加了对线圈的预弯、铲头、封焊等功能，在定子线圈热压前一次完成以上各工序。
But in this shaping installation, besides the mentioned functions, shaping, shoveling, soldering and sealing of the stator coils can be completed at the same time before hot pressing.
封盖可选择平行缝焊、钎焊、玻璃熔封或树脂粘结。
The fixing and sealing may choose among parallel - seam welding, braze welding, glass - melting - sealing and resin binding.
聚酯膜有感结构，环氧树脂包封，体积小，重量轻，引线直接焊于电极，损耗小。
Polyester film feeling construction, inductive, epoxy resin coating. Small size and light weight. Small dissipation factor, the leads directly welded to electrodes.
MOSFET的封装主要由晶圆切割，晶粒黏贴，焊线，封塑，切割成型这五大流程组成。
The assembly of MOSFET is consisted of five main processes, which are wafer sawing, die attach, wire bond, molding, trim and form.
通过对HP295焊瓶钢制作的钢瓶封头缺陷进行分析，找到了影响钢瓶封头拉延性能的原因。
The influencing factors of drawing properties for the cylinder end-heads were analyzed by checking out the defect of cylinder end-heads which made of HP295 steel.
此外，副通道以所需的一定间隔横向或斜向焊封或胶粘而分隔成纵向节段；
Two vertical edges of the utility model are overlapped and welded up or glued to form a main channel and an assistant channel.
此外，副通道以所需的一定间隔横向或斜向焊封或胶粘而分隔成纵向节段；
Two vertical edges of the utility model are overlapped and welded up or glued to form a main channel and an assistant channel.
应用推荐