中插缓和曲线是工程中常见的一种缓和复曲线的组成部分。
Insert transitive curve is a common component curve in engineering.
单凸轮连杆组合机构可克服上述缺点,即可以方便地再现预定轨迹并有精确解,但其缺点是难以实现内凹曲线的轨迹复演。
Single CAM linkage mechanism can overcome the shortcomings mentioned above, however the new problem is that the mechanism can not generate the path which has concave curve.
本文把在单连通区域上成立的曲线积分与路线无关性定理推广到复连通区域。
In this paper the theorem in which a curve integral is independent of the integral path on a single connected region is generalized.
设B是一个复的向量空间,它是由环链在平环上的简单闭曲线生成。
Let B be a complex vector space generated by some simple closed curves in the annulus.
本文就非闭光滑曲线上关于第二类边界条件的复三次样条函数的逼近误差进行了论讨,取得了较好的结果。
In this paper, we discussed the approximation errors of complex cubic interpolation spline on open smooth curves under the second boundary condition and got the better results.
采用电化学交流阻抗法和极化曲线法研究了环境友好型缓蚀剂钨酸盐及其复配对模拟水中碳钢的缓蚀作用。
The inhibition effect of environmental friendly inhibitors such as tungstate and its complex for carbon-steel corrosion in simulated water is studied by using AC impedance and polarization curves.
讨论曲线上柯西型奇异积分利用三次复样条进行近似计算的误差估计,对于相关函数类给出了这类逼近的误差阶。
This paper discusses the estimation of approximation orders of singular integrals over a general curve by means of cubic complex spline.
研究复双曲空间中的全纯曲线。
In this article holomorphic curves in the complex hyperbolic space are discussed.
本文在复连域上引进势函数的概念,并给出其计算方法,以此来解决一些复杂的曲线积分计算问题。
This paper introduces the concept of potential function into the multiply-connected region and provides its method of computation in order to solve some complex problems concerning line integrals.
加载压力被单独为各自的骑辊加压,根据压区压力要求和各自的复卷长度,相关的纸卷直径,根据在TRUTEC设定的曲线。
The loading pressure is calculated separately for each rider roll depending on the required nip pressure and respective sheet length. The related diameter–dependent set curve is stored in TRUTEC .
借助于复反应分析技术,用确定性方法求得复杂结构的离散传递函数曲线。
The transfer function of the earthquake response of the complicated structures is computed by numerical method using deterministic complex response analysis.
在唐钢150t复吹转炉上开发出适用于百吨以上顶底复吹转炉的音频化渣技术,并根据音频曲线实现了转炉吹炼操作的量化分级管理。
The technique of audio frequency slag melting has been exploited for top and bottom combined blown converter in 150 t combined blowing converter of Tangshan Iron and Steel Company.
该方法将平面上的一段圆弧曲线表示为参数复有理函数的形式。
The representation has no weight factors or control parameters, and it is geometric and affine invariant .
以锌盐、葡萄糖酸盐为主要缓蚀成分复配的适用于天然海水中碳钢的高效缓蚀剂,采用极化曲线、循环伏安曲线和交流阻抗谱图分析了该缓蚀剂的阳极脱附行为。
The adsorption and anodic dis-adsorption action of corrosion inhibitors for carbon steel in natural seawater was studied by electrochemical methods such as polarization, cycle polarization, and EIS.
对静压桩进行了隔时复压试验和静载试验,静压桩的极限承载力随时间呈双曲线增长。
The re-pressed tests to statically pressed pile after different times, as well as the ordinary pile bearing capacity tests were performed.
通过复水比曲线我们可以看出在前几分钟内曲线成上升趋势,随着时间的增加海参吸水量逐渐减少,曲线成平稳下降趋势。
Through the water than the curve, we can see the first few minutes into a curve upward trend With the increase in sea cucumbers water decreased gradually, as a smooth curve downward trend.
通过复水比曲线我们可以看出在前几分钟内曲线成上升趋势,随着时间的增加海参吸水量逐渐减少,曲线成平稳下降趋势。
Through the water than the curve, we can see the first few minutes into a curve upward trend With the increase in sea cucumbers water decreased gradually, as a smooth curve downward trend.
应用推荐