本文建立了一种计算含孔筒壳破坏应力的简便方法。
This paper Presents a simple method developed to predict the failure pressure of cylinders with holes.
本文讨论了叉筒网壳的建筑造型方法和空间特点、结构布置形式、结构支承方式等方面的内容。
In this paper architectural shapes and space characteristic, structural forms of latticed groined barrel vault and its support methods are discussed.
采用有限单元法对升船机卷筒结构进行整体计算，提出了有限元分析的力学模型，对筒壳、幅板的强度及刚度作了全面分析。
The paper USES finite element method to calculate the whole reel structure of a ship lift and presents the mechanical model of finite element analysis for the structure as a whole.
在基本假设的条件下，导出了筒形离心式通风机筒壳内气体流动速度的近似计算公式。
With the condition of the basic hypothesis, the approximate calculation formula was worked out on the gas folwing speed in the tubular centrifugal ventilator.
模拟计算结果表明：与其他领域应用的旋风分离器相比，五边形入口、三心大涡壳式旋风预热器内筒入口附近次级流动相对较弱；
The results of the simulation indicate:compared with cyclone in other domain, the secondary flow of the preheating cyclone with pentagonal inlet and three core volute structure is relatively weaker.
核电站安全壳是防止放射性物质向环境释放的大体积预应力混凝土筒壳结构，是特殊环境条件下的重点防护目标。
Nuclear power plant containment shell is a large-volume pre-stressed reinforced concrete silo-shell structure to prevent radioactivity, and is the most important protected object in special condition.
本文将反应堆压力壳的球顶盖、上下法兰、螺栓、筒体及双道O形环作为一个超静定系统进行了应力和变形分析。
The reactor pressure vessel composed of spherical top and lower heads, upper and lower flanges, bolts, cylinder and two O-rings, as a static indeterminate system has been studied.
在奥氏体不锈钢制再沸器的上管板与壳程筒体焊接的管板一侧发生蒸气泄漏。
The steam leakage was occurred on the welding zone of the tube sheet of the austenitic stainless steel heat exchanger.
建立了通过变厚度筒壳把球壳与不等厚的筒壳相连接的不连续应力解析计算方法。
The analysis method which can calculate the stress of the changing wall thickness section connecting the sphere head and the cylinder shell with unequal wall thickness has been established.
栓壳是筒形，并在嵌合状态与配置于内窥镜内部的管路连通。
The plug frame is cylindrical and communicates with a pipe line disposed inside the endoscope.
本文提出了一种用于筒体高层结构弹塑性地震反应分析的杆系——柱壳计算模型。
A calculation model of bar system-cylindrical shell to be used for elastoplastic analysis of earthquake response of reinforced concrete tube structures is given in the thesis.
采用有限元分析方法，根据提升绞车卷筒筒壳的结构和工作情况建立了筒壳的三维计算模型。
According to lifting hoist reel tube shell structure and work situation, a 3-d calculated model of tube shell has been established with finite element analysis method.
浑水泥浆泵是单级单吸立式离心泵，主要螺杆泵部件有蜗壳、叶轮、泵座、泵壳、支撑筒、电机座、电动机等组成。
Sewage slurry pump is single stage single suction vertical centrifugal pump, the main components are volute, impeller, pump base, pump casing, support tube, motor base, motor and other components.
灯泡壳由链条带动至链条末端，随着承接筒的翻转，灯泡壳脱离承接筒而掉入封口机中。
The bulb shell is driven to the terminal end of the chain by the chain. When the receiving barrel is turned, the bulb shell which disengages from the receiving barrel falls into the sealing machine.
灯泡壳由链条带动至链条末端，随着承接筒的翻转，灯泡壳脱离承接筒而掉入封口机中。
The bulb shell is driven to the terminal end of the chain by the chain. When the receiving barrel is turned, the bulb shell which disengages from the receiving barrel falls into the sealing machine.
应用推荐