推导了这些误差的当量啮合误差的计算公式，分析了系统的均载特性。
The formula of equivalent mesh error has been deduced, the load sharing coefficient has been computed.
三牙轮钻头主要零件形状复杂，影响钻头直径及牙轮齿圈啮合误差的因素较多。
There are many factors influencing the bit diameter and the tooth row intermesh due to the complicated shapes of the main parts of a three cone bit.
本文主要是讲述如何采用普通仪器，普通方法以及通用工具来解决镶片大模数齿轮滚刀啮合误差的难题。
This paper describes how to use common equipment, ordinary common tools and methods to solve large-scale tipped several Hob meshing error problem.
建立了两级星型齿轮传动系统的非线性动力学分析模型，模型中考虑了系统的综合啮合误差、时变啮合刚度以及齿侧间隙。
A dynamic analysis model in which the gear error and the time-varying stiffness and backlash are included is established for a 2-stage star gear train.
此文给出了按平面啮合原理设计矩形花键滚刀齿形的误差计算方法，并计算了几种规格的滚刀的齿形误差。
This paper gives a calculating method of the error of rectangle spline hob profile designed on the theory of plane engagement, with the errors of some hobs calculated.
以啮合理论为基础，导出了蜗式凸轮机构从动件(即分度转盘)在凸轮实际轮廓和实际机构尺寸诸因素的影响下，分度误差的计算公式。
Based on meshing theory, a formula is derived for calculating index error of worm-type CAM follower (i. e. Tindex plate) under influence of actual worm-type CAM profile and dimensions.
本文用运动学法进行了有误差斜齿轮的空间啮合分析。
In this paper, the authors analyze the space mesh of error helical gear transmission by using kinematics.
如果以齿纹中点法剖面作为齿形检测和设计剖面，用平面啮合法设计花键滚刀时，则齿形误差最小。
If the normal section in the center of the tooth line is taken as a tooth measuring and design section, when spline hob is designed in a plane meshing, the tooth profile error is minimum.
对啮合偏移和周节累积误差分别和共同对轮齿载荷分布的影响进行了分析，并将分析结果进行了比较。
This paper has analysed load distribution of gear ring which is affected engaged deviation and cumulative pitch error, and comparing three analysis results.
由于存在修形原理误差、齿轮加工误差以及载荷工况的变化，渐开线修形齿轮在使用中仍会有啮合冲击现象。
Owing to the modified error in principle, the manufacturing error and the variation of the load, there still exists the mesh impact in the transmission of modified spur gear.
以圆矢量函数为工具，推出了误差条件下的渐开螺旋面方程，并以啮合线为媒介，建立了测量蜗杆误差补偿的数学模型。
With the tool of circle vector function, the involute helix profile with error is given, and with the media of engagement line, the error compensation mathematical model is established.
修形直齿轮因误差因素在齿对的啮入和啮出位置会出现啮合干涉或啮合间隙。
Errors of modified spur gears results in meshing interference or meshing clearance at the position of mating teeth coming into or out of contact.
该文基于空间啮合理论，利用微分几何方法首次对该种齿轮的齿形误差与齿向误差进行计算，并给出计算实例。
Based on the space gear engagement theory, a new way to calculate the profile errors and axial errors is developed for the first time and a numerical example is presented.
孔系之间的平行度误差，会影响齿轮的啮合质量。
Holes in parallel between the degree of error will affect the quality of the meshing gears.
基于齿轮副的动态啮合模型，对具有误差激励的齿轮副按长、短周期从理论上研究了其动态响应特征。
The paper researches the spectrum characteristics of dynamic response of the gear pair with the error excitation in the long and short period based on dynamic mating model of the gear pair.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
提出了运动优化的方法，通过预设传动误差抛物线函数，使齿面啮合时运动误差和不连续性减至最小。
The motion optimization method is proposed, by which transmission errors anddiscontinuousness of tooth surface meshing is decreased to minimum.
在研究滚刀加工不同齿数带轮所形成的误差分布规律及误差对带与轮啮合传动影响的基础上，确定了滚刀可加工的齿数范围与参数。
At the basis of distribution law of error formed by the processed pulley with various teeth and its effect on transmission, the scope of tooth of pulley processed is defined.
理论分析和测试结果表明：啮合法可利用齿形误差展成系统测量齿向误差。
The theoretical analysis and experimental results show that the lead error measurement may share same generation system with involute profile measurement by this meshing method.
在不增加啮合齿向误差的前提下，合理给定支承平行度要求。
Under the precondition of an absence of increase in gear mesh error a rational support parallelism can be set.
本文综合运用了齿轮啮合理论，并以磨齿加工为例，系统地研究了与渐开线性质有关的齿轮加工误差产生的啮合机理，并将其概括为传动误差、回转轴相对位置误差及刀具误差。
The machining errors of gear that relate to the nature of involute are studied with gear engagement theory and combining grinding-machining in this paper and they are summarized as transmissio.
应用具体实例，研究了加工误差对少齿差内啮合齿廓重迭干涉的影响，并提出相应的解决方法。
The way to solve the problem of the tooth outline overlap interference caused by the processing errors in the practical use is put forward.
应用具体实例，研究了加工误差对少齿差内啮合齿廓重迭干涉的影响，并提出相应的解决方法。
The way to solve the problem of the tooth outline overlap interference caused by the processing errors in the practical use is put forward.
应用推荐