在B处的单元体，弯曲应力为零。
建立了三维机织物单元体的结构模型。
The unit cell model of 3d woven structure is established in this paper.
单元体可以认为是已经分配出去的内存区。
The body of the cell is the area of memory which is considered allocated.
画出最大剪应力的单元体并标出全部应力值。
Draw the element for maximum shear stress and mark values of all stresses.
结构单元体等效直径也随固结压力的增加而增大。
The equivalent diameter of structure cell also increases with increment of consolidation pressure.
扰动因子向量的方向与材料单元体应力主方向相同。
The orientation of disturbance factor vector is the same as that of vector of material unit stress.
这种单元体具有公式简单、精度高、收敛快等优点。
The element has the advantages such as simple formulation, high accuracy, rapid convergence and so on.
非光滑试样的耐磨性随单元体分布间隔的减小而提高。
The results show that the wear resistance changes with the variety of shapes and distributing distance of the non-smooth unit.
材料中此点附近的一个单元体，其表现犹如正交晶系的晶体。
An element of the material at such a point behaves like a crystal of the orthorhombic system.
提出了画单元体应用叠加原理图解分析的方法进行内力素测定。
For inner force element measurement, the paper adopted a method of diagram analysis by plotting elements and superposition which can avoid errors.
通过将井筒分成微小单元体，对隆32井卸载过程进行了数值模拟。
The unloading process for long32 is simulated with numerical method by dividing wellbore into minim cell.
在小型单元体炉中进行了不同形状尺寸及种类的生物质燃料的层燃燃烧试验。
Grate firing tests of biomass fuels with different shapes, sizes and kinds were carried out in a miniature unit furnace.
采用三角形单元体进行经济学优化，并释放角度约束，能得到更低的运输费用。
It has been found that the use of triangular elements for performing an economic optimization along with a release of Angle constraint can result in even lower freight charges.
本课题主要研究了三维机织物的结构，还建立了三维机织物单元体的结构模型。
This article mainly studies the structure of 3D woven, and the unit cell model of 3D woven structure is established in this paper.
入射波的入射角、入射频率及单元体所处深度对动应力路径的形状有较大的影响。
There is great influence of the incident Angle, the incident frequency and the depth of the soil element on the shape of stress path.
本文根据作用在土单元体上力的平衡条件，研究了粘性土的土压力非线性分布问题。
According to the equilibrium conditions of forces acting on a soil element, the problem for non-linear distribution of earth pressure of cohesive backfill is studied.
在岩体多场耦合分析中，许多采用岩体表征单元体(REV)讨论岩体的渗透特性。
Representative elementary volume (REV) is usually adopted to discuss the variation of permeability with volume of fractured rock masses in multi-field coupling analysis.
针对一种由5个单元体组成的多单元体运动机构，介绍了其组成情况及运动控制原理。
As for a kind of 5unit mechanism, the structure and locomotive principle of these units are introduced respectively.
本文提出关于平面应力状态单元体上两个主平面与两个主应力对应关系的直观判断方法。
This paper advances a direct observational method to determine two principal planes corresponding with two principal stresses Belng simple and obvious, this method ean be mastered easily.
内存单元包括一个跟随在单元体后的单元句柄。单元体可以认为是已经分配出去的内存区。
A cell consists of a cell header followed by the body of the cell itself. The body of the cell is the area of memory which is considered allocated.
仿生非光滑表面减粘降阻研究的关键技术是非光滑单元体材料(合金白口铸铁)与钢的连接。
Joining of alloy white cast iron, as an unsmoothed surface material, and steel is one of the key techniques in study of the reduction of soil adhesion and resistance of bionic unsmoothed surfaces.
由此，当该吸附装置吸附饱满时，由活动拆离该单元体以抽换该吸附装置而以利重复更换使用。
Therefore, when the absorption device is fully filled, the unit body is movably detached to replace the absorption device so as to be favorable for repeated replacement and use.
模型考虑了管柱单元体的刚性效应及套管扶正器的影响，同时对实测井斜数据进行平滑和插值处理。
The model takes into account the effect of stiffness of the string element and the effect of casing string stabilizers, and makes smoothing and interpolation to the measured well inclination data.
随后讨论节理迹长、间距、开度、产状和组数等结构面几何特征对岩体渗透特性及表征单元体积的影响。
The factors influencing the permeability characteristic and REV size of rock masses such as trace length, space, aperture, inclination and the number of joint sets are discussed.
电磁条带较宽的推进单元体所激发的电场，磁场和电磁力都具有更好的渗透效果，但相应同深度场强值较小。
The electric field, magnetic field and electromagnetic force have better penetrated ability but less near-wall strength whiles the propulsion units of wider magnetic poles.
研究2.5D编织细观结构，分析了其单元体模型，建立了2.5 D编织复合材料弹性性能分析预报模型。
The microstructure of 2.5d braids was studied and their unit cell models analyzed, based on which a model for predicting the elastic properties of 2.5d braided composites was established.
导向器类零件分体式精铸的关键技术之一是切分得到蜡模模具设计的内、外环及叶片单元体即如何实现分割面的生成。
One of the key-technologies of guiding device investment casting is getting internal ring, external ring and blade unit by splitting integral guiding device part for wax-mold design.
在分析岩体水力耦合过程基础上，根据岩体的基本结构及代表性单元体(REV)是否存在提出了建立水力耦合模型的方法。
Based on analyzing HM coupling processes, the conceptual HM coupled models are proposed according to basic structure of rock mass and concept of representative element volume (REV).
在分析岩体水力耦合过程基础上，根据岩体的基本结构及代表性单元体(REV)是否存在提出了建立水力耦合模型的方法。
Based on analyzing HM coupling processes, the conceptual HM coupled models are proposed according to basic structure of rock mass and concept of representative element volume (REV).
应用推荐