调整厚度切割旋钮,可对推杆进行无级调速以满足不同切割厚度的要求。
Adjusting thickness-cutting knob may carry out stepless speed regulation of push rod so as to meet the requirement of different cutting thickness.
根据切割厚度和材质设置适合的加工参数,以利于提高加工效率和表面质量。
Set up appropriate processing parameters in accordance with cutting thickness and material to be propitious to improve processing efficiency and surface quality.
当你要把一根原木切割成一块块木板时,你的锯的厚度很关键。
When you cut up a log into boards the thickness of your saw matters.
香柏原木被切割成不到四分之一英寸村厚度的、小的、铅笔长度板条。
The cedar logs are cut into small, pencil-length slats less than one-fourth of an inch in thickness.
你可以使用相同的厚度用于更繁重的使用,但是应该切割的更小块一些,这样才不会因为承受的重量而开裂。
You can use the same thickness for heavier use, but should be cut a little smaller, so as not to bear the weight of the crack.
我在查询这个小词的时候,额外地发现了一个我以前不知道的新词:kerf .当你要把一根原木切割成一块块木板时,你的锯的厚度很关键。
As a bonus, in researching this little factoid I discovered a new word I hadn't known before; kerf. When you cut up a log into boards the thickness of your saw matters.
玻璃切割工人按照指定的大小和形状切割各种厚度的平板玻璃。
Glass cutters cut flat glass of various thicknesses to specified sizes and shapes by hand.
但氩气等离子弧的电压较低,焓值不高,切割能力有限,与空气切割相比其切割的厚度大约会降低25%。
But the argon plasma arc voltage, low enthalpy is not high, cutting ability is limited, and cut the air than the thickness of the cut about 25% lower.
切割电流可调,能适应各种厚度板材的加工。
Cutting current is adjustable to adapt to the various thickness of sheet metal processing.
钢带:卷起来用于加工保持架的带型钢材。通过热轧或冷轧达到一定的厚度,然后切割成一定的宽度并卷成钢带卷。
STRIP: Flat rolled steel used in the forming of cages. Hot or cold rolled to specified thickness, slit to specified widths and wrapped into coils.
本机采用变频调速,调速范围宽,能切割不同厚度的废钢,水平、垂直方向切割行程大。
So it can cut different thickness scrap steel. Its cutting route is very long in horizontal and vertical direction.
根据不同的密度和厚度,这些材料可以用CNC数控设备、喷砂设备、等离子切割设备或手动工具来加工成沟槽、凿子和锥子。
Depending on its density and thickness the material can be CNC routered, sand-blasted, cut with a hot wire system, or hand-worked with standard woodworking tools such as gouges, chisels and awls.
通过试验,分析了被切割工件强度和厚度与切割速度之间的关系。
The relationships between the cutting speed and a incised workpiece of intension, thickness are analyzed.
本文的最后部分对等离子体弧切割变厚度板材进行实验研究。
In the finality of this article an experiment study about plasma arc cutting variable-thickness plate is introduced.
所以在切割前要根据材料的厚度正确选用切割电流和相应的喷嘴。
So in before cutting the thickness of the material according to the correct choice of cutting current and the corresponding nozzle.
本次实践根据聚能药包原理,采用不同尺寸的线性聚能药包。对不同厚度的铜块体进行切割。
The present cutting practice was based on the principle of energy-concentrated charge, using linear-shaped charges of different sizes to cut copper blocks with different thickness.
美国客户急切寻求激光雕刻机用来切割不同厚度的不锈钢。
Customer from the U. s. a needs laser engravers urgently and USES it to engrave stainless steel with different thickness.
根据钢板厚度,在转角处可自动限速,有效防止过烧。支持边缘切割、偏移切割,对较厚的钢板可减少预热时间,并可避免因排料计算错误而造成的板材浪费。
Automatically control the cutting speed to avoid over-burning according to plate thickness. Possible to edge cutting, offset cutting, to avoid wasting of meal sheet caused by calculation errors.
实验验证,通过改变切割速度提高变厚度工件的切割质量是可行的。
The result demonstrated that the way of adjusting cutting speed is obtained.
本机主要用于将柱状泡绵连续地切割成一定厚度的片状,并将切成的泡绵自动烧成卷。
This machine is mostly used for round foam continuously cut definite thickness pieces, and let the shaped foam roll automatic.
美国客户急切寻求激光雕刻机用来切割不同厚度的不锈钢。
A Customer from the U. s. a needs laser engravers urgently and USES it to engrave stainless steel with different thickness.
对精确度的控制使得我们可以从其厚度和所需制品厚度一样的材料中切割出几乎任何形状的制品来。
The control of precision that we can from its thickness and the thickness of the material in the same products cutting out the shape of the products to almost any.
本文通过对电火花线切割加工工艺规律的分析,选取影响工艺效果的主要因素:工件厚度、脉冲宽度、脉冲间隔、脉冲高度,作为输入向量。
By analyzing the law of WEDM processing, this article selects the main factors affecting process: the thickness of the work-piece, pulse width, pulse interval, pulse height, as the input vectors.
在作大厚度切割时,变频跟踪应适当调慢,最好从零位起调至切割稳定,电流表指针不再激烈晃动。
When advancing large thickness cutting, frequency tracking shall be properly adjusted slow, you'd better adjust it to stable cutting from zero position and ammeter pointer no longer shakes sharply.
切割速度是与所需切割的材料厚度及材质的硬度相关联的。
Cutting speed is related to the thickness and hardness of materials to be cut.
切割速度是与所需切割的材料厚度及材质的硬度相关联的。
Cutting speed is related to the thickness and hardness of materials to be cut.
应用推荐