而其临界切削厚度与材料的硬度有关。
And its critical cutting thickness and hardness of the material relevant.
研究了不同切削厚度对竹材表面质量与屑片质量的影响。
The effects of different cutting thickness on surface quality and slice quality are studied in this paper.
通过理论计算得到了KDP晶体在不同晶向上临界切削厚度的变化规律。
The variation rules of critical cutting thickness on the different crystal and different orientation of KDP crystal are obtained by theoretic calculate.
给出了采煤机螺旋滚筒不均匀运动时截齿瞬时切削厚度计算的数学模型和程序框图。
The mathematical model and block diagram are presented to calculate the pick momentary cutting thick when the shearer drum is in the state of irregular motion.
竹材的节间、节部、切削厚度、含水率及切削速度等因素对切削阻力均有不同程度的影响。
Factors like internode, node, cutting thickness, moisture content, cutting speed could influence the cutting force in varying degree.
用滚筒式采矿头在起伏不定的微地形上切削海底富钴结壳时，需按开采要求确定其切削厚度。
When the Rotary cutting Drum for mining Cobalt-rich Crust is working on the fluctuant microtopography of sea floor, it's necessary to determine the cutting depth according to the mining requirement.
得出了切削厚度与刀具前角这两个切削参数对切削质量影响的规律，得出二者关系的数学模型。
The influencing orderliness of the cutting depth and the rake Angle of the tool on cutting qualities are found and the mathematical models are built.
通过建立KDP晶体脆塑转变临界切削厚度模型，研究了KDP晶体金刚石切削脆塑转变机理。
Through establishing a model of critical cutting depth during the occurrence of brittle-ductile transition of KDP crystal, the mechanism of brittle-ductile transition of KDP crystal is studied.
从单颗金刚石最大切削厚度的角度，分析了磨削深度、进给速度和砂轮线速度对磨削力的影响。
The influence of depth of grinding, feed rate and circular linear speed of the grinding wheel on the grinding forces with respect to the maximum chip thickness of a single active diamond was analyzed.
最小切削厚度的获得是反映超精密切削加工水平的重要标志，因此对极薄切削进行分析具有重要意义。
It is a sign of the machining level of ultra-precision cutting reflected by the achieving of minimum cutting thickness. And it will be significant to the analysis of extra thin cutting.
本文提出了一种通过改变滚刀每个刀齿的切削厚度与切削宽度的，新型的高生产率滚刀—轮切式齿轮滚刀。
A new type of productive hob which can change the cut width and depth on each tooth of the hob is presented in this paper. It's title is turn cutting hob.
分析了超微细切削加工的机理、特点及技术难点，并对最小切削厚度与刀具刃口圆弧半径的关系进行了量化分析。
The mechanism, features and difficult problems in superfine machining are analyzed. The relationship between the minimum cutting thickness and the circular radius is confirmed.
此外，他们认为，对于攻丝存在一个临界切削厚度(螺纹深度)值，在临界切削厚度的范围内，攻丝能降低攻丝扭矩。
In addition, they believe, for tapping there exists a critical cutting thickness (thread depth) value of the critical cutting thickness within the tapping can reduce the tapping torque.
它等于旋削中的切屑宽度或者等于线性切削中的切屑的厚度。
Rotary cutting it to the chip or equal to the width of the linear cutting chip thickness.
在切削实验中，可对切屑厚度、刀具磨损及螺纹等的形貌进行观察并测量其尺寸。
In cutting experiments, it can be observed and measured that the chip thickness, the tool wear, the screw thread teeth, and so on.
建立了三维切削下切屑厚度的数学表示，提出了递延累加切屑厚度计算算法。
The calculation formula of the chip thickness was established under 3D cutting process and an uncontinuable adding up calculation algorithm of the chip thickness was proposed.
激光切削前后对角膜进行测厚，计算角膜瓣厚度。
Thickness of cornea and corneal flap were measured and calculated before and after laser cutting.
激光切削前后对角膜进行测厚，计算角膜瓣厚度。
Thickness of cornea and corneal flap were measured and calculated before and after laser cutting.
应用推荐