如同罗曼史一般,脖子变形也有许多不同的原因。
一个圆柱体外壳的曲度变形情况受到其本身的结构限制和不确定的外力影响,一般可以通过数据模型方程序测算出它的结果。
Cylinder buckling is governed by imperfections in a structure and uncertainties in the loading of weight, and mathematical models can predict this behavior.
第三种情况是因为传动轴变形不平衡引起,一般这种情况出现在底盘碰撞过的车比较多。
The third case is due to the deformation of the transmission shaft caused by the imbalance, the general situation in the chassis collision over the car.
实木复合门:主要是实木做骨架,表面贴高级木皮做的门,造型一般非常美观,价格合理,主要的优点是不变形,不开裂。
Solid mu fu closes the door: mainly is real wood frame, make the top surface veneer, modelling generally do very beautiful, the price is reasonable, the main advantage is not deformation, no crack.
虽然这样做不知何故总是挡住他的眼睛,我们就像试验一般的让这种变形具备可能性。
Although this hides his eyes somehow, we felt like experimenting with the possibilities that could give these deformations.
而且,证实建立在某种试验应力状态下饱和软粘土循环强度和循环累积变形的变化规律,可以推广到一般应力状态下。
And the changing laws of cyclic strength and cyclic accumulate deformation built on certain test stress states have generality and can be used in general stress states.
辊锻过程中金属变形及流动,与一般模锻工艺相比存在较大的差异,因而其工艺设计及初成形道次模具、整形模具设计也不同于常规模锻工艺。
The deformation and flow of metal in the process of roll forging are much different from those of ordinary die forging, So are the design of its technology, preliminary forming dies and dressing dies.
不失一般性,忽略不计剪切变形。
Without loss of generality, shear deformations will be neglected.
不失一般性,忽略不计剪切变形。
Without loss of generality, shear deformations will be neglected .
剪切应力还控制翡翠绿色色相和绿色空间的分布。绿色一般分布在韧性变形区的中心部位,高应力区有利于铬的富集。
In general, the green color is distributed in the center place of ductile deformation area, the high stress is of great advantage to the concentration of chrome.
一般情况下,模型栅格的变形是轴向应变和切向应变的组合。
In general, the deformation of the model grille is a combination of axial and shear strains.
大变形围岩的锚杆支护设计一般还是采用经验类比法,主要原因之一是不能合理确定锚杆的承载能力。
The bolting design of large deformation surrounding rock usually depends on experience, one of the main reasons is the bearing capacity of bolts.
就混凝土自身而言,产生裂缝的机理一般认为是因为混凝土材料变形受约束所引起的内应力大于材料抗拉强度的缘故。
The mechanism of crack is that internal stress in concrete material caused by its restricted deformation is greater than tensile strength of material generally.
用TL法分析研究,建立了二维弹性大变形接触问题的一般实用有限元分析模型。
A general practical finite element analysis model for two-dimentional elastic large deformation contact problems was established using the TL method.
因此悬索在一般荷载下的变形和振动问题便是一个较为复杂的几何非线性问题。
The deformation and vibration analysis of cables under common loads is therefore a complex nonlinear problem as geometric non-linearity is generally involved.
本文从有限弹性理论出发对超弹性薄膜轴对称大变形问题进行了一般的数学描述。
In this paper, the problem of large axisymmetric deformation of hyperelastic membrane is reformulated on the basis of the general theory of finite elasticity.
因此索网在一般荷载下的变形和振动问题便是一个较为复杂的几何非线性问题。
The deformation and vibration analysis of net cables under common loads is therefore a complex nonlinear problem as geometric non-linearity is generally involved.
采用复级数方法首次建立了基于一阶剪切变形理论的各向异性矩形板横向弯曲一般解析解。
General analytic solutions for transverse bending of anisotropic rectangular plate using first order shear deformation theory is obtained at the first time by the complex series method (CSM).
这种变形一般是非弹性的,其大小取决于框架中每个组成部分的相对强度和刚度。
These deformations are nonelastic, depending on the relative strength and stiffness of each component of the frame.
在水面舰艇机械的传统设计中一般不考虑机架伸缩变形对机构运行的影响。
The influence of engine frame distortion on crank rocker operation is not taken into account in traditional surface vessel design.
不同的装配—焊接顺序,焊后产生不同的残余变形,一般是先点固,再进行对称焊接。
Different assembly-welding sequence may result different risidual deformation, we usually take fixup by spot welding first, then take welding symmetrically.
一般在土体粘性差,对变形位移要求较严格的情况下,采用喷锚支护较安全可靠;
The concrete spray bolting is generally suitable only to low-viscosity, high-deformation or displacement soil so that safety of foundation pit can be guaranteed.
给出了一般情况下用本技术测量和计算材料机械变形方向的方法,列出了本技术测量的实验数据和结果。
Using the proposed technique the measurement and calculation method of material mechanical deformation direction is described. Finally, the experimental results and test data are given.
但是,因高差引起的变形很难通过一般的多项式纠正方法进行改正。
But the distortion of SAR image brought by elevation is very difficult to be corrected by polynomial rectification.
本文对非比例双滑移的变形规律和运动学进行了一般的数学分析。
This paper presents a general kinematical analysis for nonproportionaldouble slip in fcc and bcc crystals.
通过对变截面多跨不等高排架位移条件的分析,导出了此类结构在一般荷载作用下的柱顶剪力及变形计算公式。
Formula for calculating shear and displacement of the top of column in bentuncler general load has been proposed the basis of analysis of displacement conditions ofbent.
通过对变截面多跨不等高排架位移条件的分析,导出了此类结构在一般荷载作用下的柱顶剪力及变形计算公式。
Formula for calculating shear and displacement of the top of column in bentuncler general load has been proposed the basis of analysis of displacement conditions ofbent.
应用推荐