使单体混合物在模腔 内聚合、固化。
The monomer mixture receives polymerization reaction in the cavity for hardening.
该模腔内注入甲基丙烯酸酯类树脂的单体混合物。
A methacrylic resin monomer mixture is filled in the cavity.
这种利用多模腔的设计也具有准椭圆传输函数特性。
The new designs utilize over-moded cavities and also exhibit pseudo-elliptic transfer functions.
确定了锥形模膛的最小长度、模腔锥角与毛坯长度的关系;
The minimum depth of conical die and the relationship between coning of die cavity and workpiece length are determined;
振动力场的引入,有利于缩短充模时间,提高瞬态模腔压力。
Introduction of vibration force field is beneficial to shorten, filling time and increase transient cavity pressure.
机器模腔表面采用特制铝合金板,热传导效率高,抗拉强度好,寿命长。
The machine mould antrum is made of special ainico main plate with good efficiency for high heat exchange , top class anti-extension and can be use for a long time.
熔融金属浇注模腔并凝固后所获得的具有成品轮廓或接近成品轮廓的产品。
Casting - an object at or near finished shape obtained by filling a mold with molten metal and allowing it to solidify.
这一工具为多相流模拟中模腔内部滑移影响的深入研究提供了便利和有效的工具。
Such a useful tool will provide the convenient and effective way for the further and more profound research on the influence of slip effect inside the mould cavities by multi-phase simulation.
液压缸压力转换熔融塑料在模腔的填充平衡需要液压缸压力驱动螺杆前进来保证。
Hydraulic pressure switchover the packing of the melt in the mould cavity has to be balanced by the hydraulic pressure driving the screw forward.
在板金上,拉伸是一个通过冲床将平板金属冲入模腔拉成中空形状工件的工艺过程。
In sheet metal, drawing is a process of forming flat sheet metal into hollow shapes by mean of a punch that causes the metal to flow into the die cavity.
大管径管路会帮助气压延迟传递到模腔,并由此可能会导致在零件上留下延迟印记。
Larger diameter hoses can help to increase gas pressure delay to the cavity and may result in hesitation marks on the part.
结果表明,纤维取向分布主要取决于模腔几何形状、纤维含量和注射工艺条件等因素。
The results showed that the fiber orientation distribution was mainly dependent on the shape of the cavity, fiber contents and molding condition.
研究了两个偶极偶极力关联的等同双能级原子与三模腔场六光子共振相互作用的辐射谱。
The emission spectrum for a pair of dipole dipole coupled identical two level atoms interacting with three mode cavity fields resonantly through 6 photon process has been studied.
布料系统采用独特的强制式破拱装置,适应不同产品的模具模腔布料,布料均匀无死角。
The Feeding system use a unique forced arch-breaking device, suitable for different mould cavity products fabric, evenly without dead ends.
熔体在模腔里冷却,硬化,直至完全固化。然后将模子打开,推出工件,并重复以上工序。
Here, the melt cools and hardens until fully set-up. The mold is then opened, the piece ejected, and the sequence repeated.
的翻译是:在结构设计的波纹管密封圈联合和它的多个模腔模具设计中引入了这一份文件。
The Structure designing of bellow seal joint and it′s multiple cavity mold designing are introduced in this paper.
提出一种利用一个二能级原子与一两模腔场的非共振相互作用制备纠缠压缩相干态的方案。
It is based on the nonresonant interactions of an atom with two field modes located in two separated cavities.
最后,设计了使用E面交叉耦合滤波器和E面多模腔滤波器的构成的紧凑结构毫米波双工器。
Finally, new, compact millimeter-wave diplexers which employ cross-coupled E-plane filters and E-plane filters with over-moded cavities are analysed.
纤维的渗透率是RTM成型工艺的一个重要参数,它对树脂在模腔中的流动状态产生重要影响。
The permeability of glass fiber is one of the important parameters of RTM process which will have influence on the flow of resins in mould.
本文介绍了在模锻工艺中实现局部加载的方法,编制了计算局部加载时模腔充填效率的电算程序。
The method of applying local loading to die forging was introduced in this paper. And a program for calculating the die filling efficiency was developed.
该机为模腔冲压成型,链式分离脱模,主要用于夹心奶糖成型生产,烫型可依据客户的要求订购。
This machine for die cavity stamping forming, chain separation stripper, mainly used for sandwich roll forming production, very hot type can be according to the demand of the customers order.
通过实验的方法测量出不同模具的喷嘴压力曲线,证实模腔几何形状与喷嘴压力之间存在确定的关系。
Experiment methodology that measures the nozzle pressure of different molds has been proposed which proved that there existed the internal relationship between nozzle pressure and shape of cavity.
介绍了塑胶模具复杂型腔采用CNCEDM的拷贝法和展成法加工技术,使镶拼式模腔改为整体式模腔;
Duplication and generation technologies with CNCEDM in machining complicated cavity of plastics dies, resulting in integral cavity instead of mosaic one, are stated.
生物质颗粒燃料的生产技术主要有两种方式,一种是热压缩挤压成型技术,另一种是高压模腔成型技术。
Biomass pellet fuel production technology mainly has two ways, one is a hot compression extrusion molding technology, the other is a high pressure cavity forming technology.
本发明引入四个主要的可变量,停 留时间、链长度、链速度以及处于同时接合状态的闭合的模腔的个数。
The invention incorporates four main variables, dwell time, chain length, chain speed and the number of closed die cavities in simultaneous engagement.
本发明引入四个主要的可变量,停 留时间、链长度、链速度以及处于同时接合状态的闭合的模腔的个数。
The invention incorporates four main variables, dwell time, chain length, chain speed and the number of closed die cavities in simultaneous engagement.
应用推荐