他买了一个带有数字控制泵的新水锅炉，并在管道周围包裹了绝缘材料。
He bought a new water boiler with a digitally controlled pump, and wrapped insulation around the pipes.
相反，我们自己的生活是由数字控制的。
一个数字控制装置主要用于将想要的颜色添加到指甲上，。
A digital control device is then used to programme the desired colour on to the nails.
对于数字控制造成的控制延迟，提出了状态观测器的设计。
Because of the control delay of the digital control, the design of the state observer is presented.
UPS逆变器的数字控制是实现全数字控制ups的关键。
Digital control for UPS inverter is a key point in full digital controlled UPS.
系统通过X-Y数字控制移动平台实现测点点阵的自动定位；
The system realizes auto-positioning the measurement points array through the X-Y digital control slider.
利用数字控制技术对位置信号误差角进行了实验检测及校正。
It has made experiment detection and rectification with signal control technology for the position signal error.
数据采集是分布式数字控制(dnc)系统的一个重要功能。
II Data acquisition is an important function of Distributed Numerical Control (DNC) systems.
介绍一种以igbt为功率单元的全数字控制脉宽调制变频装置。
A fully digitally controlled SPWM inverter with IGBTs as the main power devices is introduced.
数字控制的时延补偿应用于直流开关电源中获得了较好的控制效果。
The time delay compensation of digital control for DC switch-mode power supplies improves the control effect.
在实现全数字控制的同时还实现了多种智能算法的柔性化设计和应用。
The flexible design and application with many intelligent algorithms are implemented as well as the fully-digital control.
本文将讨论空调系统中空气处理机组的直接数字控制（DDC）设计。
This paper discusses the direct digital control (DDC) in the air-handing unit of air-conditioning system.
采样控制作为一种数字控制的直接设计方法，近年来引起了广泛的重视。
As a direct design procedure for the digital controller, sampled data systems control has received wide attention in these years.
该电路采用ARM嵌入式处理器和先进的控制策略，实现了全数字控制。
The circuit was realized in full-digital control with ARM embedded processor and advanced control strategy.
本系统采用DSP实现数字控制，以达到体积小、成本低、智能化的要求。
By using the DSP digital control technique, this EPS system realized the requirements of intelligent and low cost.
它是机构学理论﹑机器人技术﹑数字控制技术和机械结构技术相结合的产物。
It is the combination among theory of mechanism, robotics techniques, numerical control techniques and mechanical structure techniques.
发数字式流量阀采用数字控制方式，调节系统流量以达到液压系统调整目的。
The digital flow rate valve regulates digitally system flow rate to implement speed regulation in hydraulic system.
该系统在生产全过程中实现计算机控制，主电机传动采用数字控制传动装置。
It is a computer control system for whole process. The drive of main-motor USES digit controlled drive.
随着电子技术的飞速发展，数字控制技术已被广泛应用于国民经济的各个领域。
Along with the rapid development of electronic technology, digital control technique has been widely used in various fields of national economy.
说明了其硬件结构、测量算法和数字控制方法以及科氏质量流量计新的应用领域。
Measuring algorithm and digital control method as well as the new application area of Coriolis mass flowmeter are described.
定时电路一般由电源模块、面板电路和定时板组成，是功率源中的数字控制部分。
Timing circuit is usually made up of power supply unit, panel circuit and timing board, it is the digital control part of power source.
除了可以作为控制策略外，一个切换逻辑性还可以用来描绘数字控制比如状态切换。
Switching logic in addition to adding a control strategy, a switching logic can be added to a schematic for digital control such as switch status.
介绍了用于整流系统的数字控制技术的组成原理以及其组成部分的设计特点和功能。
The principles of digital control technology used in rectifying system were introduced, as well as the design rules and the characters of its components.
模糊控制是以模糊集合、模糊语言变量和模糊逻辑推理为基础的计算机数字控制技术。
Fuzzy control is a kind of computer digital control technique, which is based on the fuzzy sets, fuzzy language variable and fuzzy logic reasoning.
交流变频电驱动钻机采用VFD驱动和数字控制技术，可简化绞车结构，提高钻机性能。
AC VFD rig adopts VFD and digital control technology, simplifying the drawworks structure and improving the rig's performance.
如何方便、可靠地构成通讯网络是实施分布式计算机数字控制(D NC)系统的关键。
Forming the communication network easily and reliably is the key to the implementation of the distributed numerical control (DNC) system.
步进电机是一种进行精确步进运动的机电执行元件，它广泛地用于工业机械的数字控制。
The stepping motor is a precision electromechanical incremental actuator. It widely USES the digital approach for control of industrial machines.
数字控制是按照含有机床(刀具)运动信息程序所指定的顺序自动执行操作的加工过程。
Numerical Control (nc) is any machining process in which the operations are executed automatically in sequences as specified by the program that contains the information for the tool movements.
借助于DSP强大的运算能力和丰富的外设来实现数字控制算法，简化了硬件电路的设计。
By powerful operation capacity and external Settings of DSP, digital control algorithm is realized and electric circuit is simplified.
这其中包括了第二代单晶涡轮机叶片材料、金属粉圆盘以及改良的全部授权电子数字控制。
These include second-generation single-crystal turbine blade materials powder metal disks and an improved full authority digital electronic control.
应用推荐