简述了定时中断程序各模块的主要功能。
Module functions of the timing interruption program are described.
命中此点则执行指定的操作，但不中断程序的执行。
Hitting this point performs a specified action but does not break program execution.
追踪点可以让您追踪程序的执行，而不会中断程序。
Tracepoints enable you to trace execution of your program without breaking.
当执行到达一个断点或发生异常，调试器将中断程序的执行。
The debugger breaks execution of the program when execution reaches a breakpoint or when an exception occurs.
你的中断程序完成一些工作，确定一个延迟程序调用(的时间)，并返回。
Your interrupt routine does a little bit of work, schedules a DPC, and returns.
文中还详细叙述了一种中断管理方法，并用实例介绍了中断程序的设计特点。
An interrupt handling scheme has been presented and achieved also. At last the design of the interruption program is introduced through examples.
介绍了系统软件的基本设计思路，给出了伺服DSP定时中断程序的基本流程。
The basic ideas for software programming of the control system are given along with the working flow of DSP's interrupt programs.
如果该条件不为真，则断言失败，中断程序的执行，并显示“断言失败”对话框。
If that condition does not hold true, the assertion fails, execution of your program is interrupted, and the assertion Failed dialog box appears.
软件采用汇编语言编写，包括初始化、按键及相应子程序、外部和串口等中断程序。
The software is programmed in assembly language, including initialization, key-press and interrupt program such as corresponding subprogram, external and serials.
软件设计主要包括主程序、PWM中断程序、电流PI调节程序、速度MRAC调节程序。
The software programs include main program, PWM interrupt program, PI control program of current and MRAC control program of speed.
当指定表达式的值改变时，监视点将中断程序执行，但必须在表达式中所使用的变量在作用域中时设置监视点。
A watchpoint will break program execution when the specified expression changes value, but it must be set when the variables used in the expression are in scope.
最后提出了整体系统的具体设计方案，给出了系统硬件框图，主程序流程及DSP中断程序流程。
At last, the thesis explicates the scheme of whole system and presents the system hardware frame diagram, main flowchart and DSP break-off flowchart.
红外发射程序的关键是定时时间到时调用中断程序来产生载波信号，对按键信号和载波信号进行调制。
The key of the infrared sending program was calling the interrupt subroutine to produce the carrier wave and modulate it with the key signal.
整个电路采用模块化设计，由主程序、中断程序、发射子程序、接收子程序、显示子程序等模块组成。
The whole circuit USES modular design, by the main program, interruption program, launch subroutines, receiving subroutines, display subroutines etc module.
这种情况下，gdb会获得控制并中断程序，从而可以让您检查所有事物的状态，如果运气好的话，可以找出原因。
In this case GDB will take control and interrupt the program, allowing you to examine the state of everything and hopefully find out why. To provoke this scenario we'll use an example program.
本文通过分析通用异步通信器件的工作原理，给出了一种利用单片机的定时器中断程序实现异步通信的方法，并在实际工程项目中得到了应用。
Based on the principle of UART, a software method has been presented for asynchronous communication by using interrupt program of timer, and has been implemented in an application project.
现在，可以调用这个方法并在循环的任意位置中断执行，这会捕获程序的状态。
You can now call this method and interrupt execution at any point of the loop, capturing the state of the program.
除了必要的模块包含及变量声明之外，信号中断捕捉程序被定义为允许输出每个数据运行的相关的头文件。
In addition to the necessary module includes and variable declarations, the signal-interrupt catcher is defined to allow the associated header for each data run to be printed out.
如果测试失败，就报告错误消息，指出故障点，同时程序执行中断。
If a test fails, an error message is reported, indicating the point of failure, and program execution halts.
这就是SAX的真正用途所在：在程序中断处理过程并进行修复之前，允许接收可能错误的数据或者错误状态。
That's where SAX can really help: it allows you to receive possibly bad data or error conditions before the program halts processing and gives you a chance to make course corrections.
此时，break语句导致程序执行中断while循环，跳转到else子句。
At this point, the break statement causes program execution to break out of the while loop, skipping the else clause.
减少延迟的线程中断处理程序
例如，您可以运行程序，设置界限，监视与服务进入中断点，通过程序指示的步骤，检查变量，并检查访问栈。
For example, you can run programs, set line, watch and service entry breakpoints, step through program instructions, examine variables, and examine the call stack.
这个表格包含中断与中断服务程序之间的处理器的映射，必须由程序员进行初始化。
This table contains the processor's mapping between interrupts and interrupt service routines and must be initialized by the programmer.
以内核模式运行的某些程序包括中断处理程序和内核进程。
Some of the programs that operate in kernel mode include interrupt handlers and kernel processes.
驱动程序将根据中断的优先级次序来执行数据操作。
Your driver will perform some data manipulation based on a sequence of interrupts.
本文通过模拟各种中断，尽可能地帮助设备驱动程序开发人员测试中断服务例程。
This article helps device driver developers test the interrupt service routine as much as possible by simulating the various interrupts.
此类限制通常是对应用程序的某些部分实施的，比如中断处理程序，其响应中断的代码必须在给定的时间范围内完成工作。
Such restrictions are typically placed on sections of the application such as an interrupt handler, where the code responding to the interrupt must complete its work in a given time period.
这个变量假定中断处理程序和该锁之间没有交互。
This variant assumes no interactions with interrupt handlers and this lock.
这个变量假定中断处理程序和该锁之间没有交互。
This variant assumes no interactions with interrupt handlers and this lock.
应用推荐